background image

1

2

4

190

178

75

ap

pr

ox

. 1

14

ap

pr

ox

. 1

08

39

5

2

NOTE: 
Excessive tightening compromises

the protection class.

The  following  is  to  be  considered

when assembling the sealing plug:   

1 . Only the sealing plug belonging to

the cable gland (

5

) may be used.

2. The head side of the sealing plug

must be on the outside  (

5

).

3. The  sealing  plug  (

5

) is  to  be

 pushed  into  the  cable  gland  as

far as it will go.

Assembly and installation

Loosen  the  cover  screws 

(

2

)

and

remove  the  cover 

(

1

)

(see  device

overview). Insert the lower part into

the  opening 

(

3

)

using  four  4  mm

screws  with  a  head  diameter  of  6

mm to 7 mm and fasten to the wall

or ceiling or onto a plate. If the head

diameter of the screws is too small,

suitable washers of 6 mm to 7 mm in

diameter are to be used in addition.

Lead the connection lines through the

screwed cable connectors (KLE) 

(

4

)

and  connect  them  to  terminals  in

accordance with connection diagram. 
For  the  pre-installed  cable  glands,

only  lines  are  to  be  used  which

have a sheathing diameter Ø of 5.5

mm to 1 3 mm, since otherwise the

IP66 housing protection class is not

ensured. 
The  tightening  torque  of  these

 screwed cable connectors is 3.5 Nm.

The  tightening  torque  of  the  cover

screws is 1 .2 Nm.

Dimensions

Maintenance

The telephone connecting relay type

mTAR  contains  no  parts  that  need

maintaining.

Maintenance and servicing

The  equipment  contains  no  parts

that need maintaining. The specifica-

tions  of  EN  60079-1 7  regarding  the

regular  inspection  of  explosion  pro-

tection are to be adhered to.

Start-up

After  it  has  been  connected  to  the

telephone network, the device is ready

for electrical operation.

Requirements

none

CE symbol

 

 

We hereby declare this product is in compliance with the Essential

Health and Safety Requirements of

ATEX Directive 2014/34/EU, EMC Directive 2014/30/EU, 

Low Voltage Directive 2014/35/EU and RoHS Directive 2011/65/EU.

The appropriate standards, technical regulations and specifications

you can take from the attached conformity declaration.

 

External view 

Internal view 

3

Summary of Contents for mTCR







Reviews: