Audix CPA240 Manual Download Page 17

Page: 17 / 40

CPA240 Configurable Power Amplifier

Page 17 of 35

21031 CPA240 manual V1.31.doc

•

Second amplifier group: Set CH3 M/S switch to ‘master’ and CH4 to ‘slave’ (this parallels

channel 4 to channel 3 master).

•

Wire/configure first amplifier group input/output signals to CH1 (master).

•

Wire/configure second amplifier group input/output signals to CH3 (master).

1 x 240 Watt.

•

Set all Master/Slave switches to ‘slave’ this parallels channels 2, 3 & 4 to channel 1 master

•

Wire/configure channel 1 input/output signals to amplifier channel 1 etc.

4.3 Audio Bus Selector

The Audio Bus allows an amplifier within a system to be connected to a switching matrix such

as an Alpha and/or other CPA240 amplifiers via a ribbon cables.

These ribbon cables couple the sixteen matrix outputs (destinations or zones) to the audio bus

channel pin headers located on the D804 connector card within the amplifier.

Configuring each amplifier master input channel involves linking the desired Audio Bus channel

(matrix zone) to the amplifier input channel using one of the four two way selector cables

supplied.

Note: See advanced configuration for:

•

Connecting two or more input channels to the same Audio Bus ‘zone’ within a single

amplifier (Chain).

•

Connecting (inserting) external signal processing equipment (Send).

4.3.1 Audio Bus Selector Configuration Examples

Connecting matrix zone output 6 to amplifier channel 1 (180W)

•

Connect one end of the two way selector cable to header 6 of the Audio Bus Channel

•

Connect the remaining end to Amplifier Channel ‘I/P’ header 1

•

First amplifier group: Set CH2 & CH3 M/S switch to ‘slave’.

•

Wire/configure first amplifier group input/output signals to CH1 (master).

Connecting matrix zone output 8 to amplifier channel 4 (60W)

•

Connect one end of the two way selector cable to header 8 of the Audio Bus Channel

•

Connect the remaining end to Amplifier Channel ‘I/P’ header 4

•

Second amplifier group: Set CH4 M/S switch to ‘master’

•

Wire/configure second amplifier group input/output signals to CH4 (master).

I/P

Chain

Send

1 2 3 4

Audio Bus Channel

Master

Slave

Master

Summary of Contents for CPA240









































Search results

Summary of Contents for CPA240

Reviews:

Related manuals for CPA240

Brands by name

Popular brands

Audix CPA240, Manual

Search results

Summary of Contents for CPA240

Reviews:

Related manuals for CPA240

Brands by name

Popular brands