manualshive.com logo in svg

Audison Thesis HV venti, Owner'S Manual, Page: 2 / 25

Share
Download
Audison Thesis HV venti Owner'S Manual Download Page 2

................ page 13

................ page 12

................ page 11

................ page 10

................ page 14

a.   Unscrew the six screws which fi x the glass panel
b.   Reassemble the glass panel. Fasten the six closing screws

................ page 14

a.   Unscrew the two screws which fi x the side handle
b.   Reassemble the side handles by fastening the proper screws

................ page 15

a.  Remove the glass panel
b.  Remove the side handle above power supply terminal blocks
c.   Lift the plexiglass panel which protects power supply terminal blocks
d.  Remove the two parts of the fuse to be replaced
e.  Eliminate all possible metallic remainders of the broken fuse and install the new one
f.   Mount power supply terminal blocks protecting panel
g.  Mount the side handle back
h.  Reassemble the glass panel

................ page 16

a.  Remove the glass panel
b.  Remove the side handle above power supply terminal blocks
c.   Lift the plexiglass panel which protects power supply terminal blocks
d.  Find the 4 blade mini-fuses
e.  Mount power supply terminal blocks protecting panel
f.   Mount the side handle back
g.  Reassemble the glass panel

................. pag. 17

a.  Remove the glass panel
b.  Set BIAS switch on “L” or on “H”
c.   Reassemble the glass panel

................ page 18

a.  Remove the glass panel
b.  Remove the bypass module
c.   Select the fi lter and the frequency you like
d.  Install the crossover module
e.  Reassemble the glass panel

................ page 19

a.  Accessories supplied with HV venti
b.  How to take the amplifi er out of its inner carton
c.   If you like to change DUAL POWER confi guration...
d.  If you like to change DUAL BIAS confi guration...
e.  If you like to install the electronic CROSSOVER...
f.   NON-PROJECTING or SEMI-PROJECTING installation (adhesive template)
g.  Remove the amplifi er fi xing plate
h.  Secure the fi xing plate
i.    Secure the amplifi er to the fi xing plate
j.    Connect signal cables...
k.   Connect power supply cables...
l.    Amplifi er calibration...
m.  Mount the grilles which cover connections onto side handles
n.  Reassemble both side handles...

a.   Fans protecting fi lters cleaning
b.   Cooling ducts cleaning

................ page 24

................ page 9

................ page 3

1 • Project purpose
2 • Project philosophy
3 • Electronics
4 • Chassis and thermal project
5 • Installation method and maintenance

................ page 2

Safety precautions
Functioning precautions
Maintenance and reliability precautions

MAINTENANCE

12 OWNER’S MANUAL

INSTALLATION

11 OWNER’S MANUAL

CROSSOVER INSTALLATION

10 OWNER’S MANUAL

DUAL BIAS CONFIGURATION

9 OWNER’S MANUAL

DUAL POWER CONFIGURATION

8 OWNER’S MANUAL

MAIN FUSE REPLACEMENT

7 OWNER’S MANUAL

SIDE HANDLES

6 OWNER’S MANUAL

GLASS PANEL REMOVAL

5 OWNER’S MANUAL

CONTROL FUNCTIONS AND PROTECTION

4 OWNER’S MANUAL

CONTROLS PANEL

3 OWNER’S MANUAL

POWER SUPPLY - SWITCHING ON PANEL

2 OWNER’S MANUAL

INPUTS - OUTPUTS PANEL

1 OWNER’S MANUAL

TECHNICAL AND ELECTRICAL FEATURES

1

TECHNICAL DATA

DESCRIPTION

2

INTRODUCTION

GENERAL RECOMMENDATIONS

1

INTRODUCTION

CONTENTS

- 1 -

i

Summary of Contents for Thesis HV venti


























Reviews:

No comments