manualshive.com logo in svg

Audison Thesis HV venti, Owner'S Manual, Page: 17 / 25

Share
Download
Audison Thesis HV venti Owner'S Manual Download Page 17

HI POWER

4 10A blade 

mini-fuses

HI CURRENT

4 15A blade 

mini-fuses

- 16 -

Pre-setting

d.  Find the 4 blade mini-fuses and set them in the confi guration you like. Before closing the 
 

product, make sure all 4 have been installed in the right position

Caution!: If the amplifi er has been connected and switched on, in order to 
change Dual Power, besides turning the amplifi er off and following setting 
you need to wait for 2 minutes before replacing the mini-fuses and to 
carefully follow the instructions for the glass panel removal. We suggest 
you use the insulated pliers supplied with the device in order to prevent 
the amplifi er from being damaged by short circuits caused by the 
capacitors charge. 
When setting the fuses, the thermal sensor wire connectors which are 
near them might get pulled off. Make sure the connectors are properly 
inserted.

b.  Remove the side handle above power supply terminal blocks:

 see

c.  Lift the plexiglass panel which protects power supply terminal blocks

a.  Remove the glass panel: see    

DUAL POWER CONFIGURATION

OWNER’S MANUAL

 8

GLASS PANEL REMOVAL

5 OWNER’S MANUAL

SIDE HANDLES REMOVAL

6 OWNER’S MANUAL

Summary of Contents for Thesis HV venti


























Reviews:

No comments