background image

128-8261

12 of 24

Page 12

ADDITIONAL REMOTE FUNCTION (AUX 2 )
Controlled By:  

Moving side switch up 3 times and selecting AUX 2 by pressing

the #2 Unlock Button. If this auxiliary output is connected to a device in your

vehicle,,,the device will immediately activate.

ADDITIONAL REMOTE FUNCTION (AUX 3 )
Controlled By:  

Moving side switch up 3 times and selecting AUX 3 by pressing

the #3 Trunk/Key Button. If this auxiliary output is connected to a device in your

vehicle,,,the device will immediately activate.

ADDITIONAL REMOTE FUNCTION (AUX 4 )
Controlled By:  

Moving side switch up 3 times and selecting AUX 4 by pressing

the #4 OPTION Button. If this auxiliary output is connected to a device in your

vehicle,,,the device will immediately activate.

TURBO TIMER MODE

This system provides a means to cool down the vehicles turbo charger, if so

equipped, by allowing the vehicle to continue to run for a prescribed period of

time every time the vehicle's engine is turned off.  This feature requires the

system to be set up for turbo timer during installation.  Consult with your installa-

tion center to be certain this feature was activated and how long the vehicle will

continue to run, 3, 5, or 10 minutes after the ignition switch is turned off.

To activate the turbo timer:

Anytime the engine is running for more than 15 seconds:

1) Place the gear selector in park.

2) Set the parking, (hand), brake.

3) Be certain your foot is off the brake pedal.

4) Press the program/Push-Button switch 2 times within 5 seconds.

The parking lights will flash two times indicating the mode was successfully

entered.

If your parking lights flashed four times, this indicates the turbo mode was on and

is now turned off.

With the turbo timer mode selected on, after you've arrived at your destination,

while the engine is still running, set the parking brake, pause 2 seconds, then

turn the ignition switch to the off position. The engine will continue to run the

allotted time according to the selection during installation.

If you do not want the vehicle to continue to run for one cycle, simply step on the

vehicle's brake, or release the parking brake, or activate the transmitter's start

button two times in succession.  Any of these will cause the engine to turn off.

TEMPERATURE START MODE:

To toggle this feature on, from the armed mode, press the side switch up 4

times than press the Lock (1) Button.  The display will switch to indicate that

the Temp Start mode was activated, and the   Icon will be displayed.  When

the temperature reaches 0° C or 32° F, the vehicle will start and run for the

allotted time for one start cycle.

NOTE:

 This feature must be active in the feature selection menu of your

system.  Check with your installing dealer to insure this feature is set to the on

position.

To cancel the Temp Start Up, simply start the vehicle either with the key or the

remote start.

CHECK TEMPERATURE

:

Move the side switch up one time and than press the Option button, #4. The

vehicle's alarm will display the temperature as shown. Temperature is read

from the alarm's module located below the dashboard.  This reading may be

higher than actual ambient temperature due to the greenhouse effect in the

vehicle and is relative only to the inside vehicle temperature.

Summary of Contents for XRO9100

























Reviews: