manualshive.com logo in svg

Audionet PRE G2, User Manual

Share
Download
Audionet PRE G2 User Manual Download Page 11

11

 

5  Inputs and outputs 

 

 

Important

 

·

 

During connecting and removing of sources or  amplifiers to the 
PRE G2 all units of your audio system have to be switched off to 
prevent  damage  of  the  PRE G2  or  any  of  the  other  connected 
units. 

·

 

Please make sure that all cables are in absolute best conditions! 
Broken  shields  or  short-cut  cables  could  damage  the  PRE G2 
and/or any other connected unit. 

 

 

5.1  Inputs 

The PRE G2 is equipped with one balanced (XLR)  1  and 5 Cinch (line) 
inputs   2   to   6   for  connecting  signal  sources  at  line  level.  Due  to  its 
double mono design, left and right channel input jacks are separated on 
the back panel. 

Please connect the left and right input of the same number printed on the 
back panel of the PRE G2 to the corresponding output of the source you 
would like to connect to the PRE G2. 

 

 

5.2  Outputs 

The PRE G2 is equipped with a pair of balanced (XLR)  8  and a pair of 
Cinch (line) outputs  7  and  9  for the left and right channel each to con-
nect the unit to your amplifier(s). The Cinch (line) output  9  is inverted. 
Due to the double mono design the left and right output jacks are sepa-
rated. 

Use  the  left  and  right  Cinch  (line)  output   7   to  connect  the  PRE G2  to 
your  power  amplifier(s)  using  high  quality  Cinch  cables.  Alternatively, 
you may connect the power amplifier using the balanced (XLR) outputs 

 8  in case your power amplifier does not support Cinch (line) inputs. 

The  inverted  outputs   9   are  primarily  designated  for  amplifiers  in 
bridged operations (in combination with the Cinch (line) outputs  7 ). 

 

 

Important

 

·

 

Bridged operations of an amplifier demand a correct setup and con-
nection.  Please  consult  your  dealer  and/or  the  manufacturer  of  your 
power amplifier to prevent damage to your equipment. 

 

Summary of Contents for PRE G2








































Reviews:

No comments

Brands by name

Popular brands

Load more brands