background image

3

1. 

Read these instructions.  

2. 

Keep these instructions.

3. 

Heed all warnings.

4. 

Follow all instructions.

5. 

Do not use this apparatus under water.

6. 

Clean only with a dry cloth.

7. 

Do not block any ventilation openings. Install in accordance with the manufactur-
er’s instructions.

8. 

Do not install near any heat sources such as radiators, heat registers, stoves, or 
other apparatus (including amplifiers) that produce heat.

9. 

Only use attachments/accessories specified by the manufacturer.

10.  Use the 24 VAC power adapter that came with the unit. 
11.  Unplug this apparatus during lightning storms or when unused for long periods of 

time.

12.  Refer all servicing to qualified service personnel. Servicing is required when the 

apparatus has been damaged in any way, such as the power input terminals are 
damaged, liquid has been spilled or objects have fallen into the apparatus, the 
apparatus does not operate normally, or has been dropped.

13.  This apparatus shall not be exposed to dripping or splashing, and no object filled 

with liquids, such as vases or glasses, shall be placed on the apparatus.

The lightning flash with arrowhead symbol within an equilateral triangle is 
intended to alert the user to the presence of uninsulated “dangerous voltage” 
within the product’s enclosure, that may be of sufficient magnitude to consti-
tute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the 
user of the presence of important operating and maintenance (servicing) 
instructions in the literature accompanying the appliance.

Caution: to reduce the risk of electric shock, do not 
disassemble the apparatus. There are no user-
serviceable parts inside. Refer servicing to qualified 
personnel.

This equipment has been tested and found to comply 
with the limits for a Class B digital device, pursuant to 
part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference 
in a residential installation. 

This equipment generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference to 
radio communications. However, there is no guarantee that interference will not occur in 
a particular installation. 

If this equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and the receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

Recycling notice: If the time comes and this apparatus has fulfilled its destiny, 
do not throw it out into the trash. It has to be carefully recycled for the good 
of mankind, by a facility specially equipped for the safe recycling of electron-
ic apparatii. Please contact your local or state recycling leaders for assistance 
in locating a suitable nearby recycling facility. Or, contact us and we might be 
able to repair it for you.

Important Safety Instructions

Summary of Contents for BLX-1K













Reviews: