manualshive.com logo in svg

Audio Technica ATUC-50, Instruction Manual

Share
Download
Audio Technica ATUC-50 Instruction Manual Download Page 50

50

Using the Charger

LED indicators

· Charging (lights red)

· Charging complete (lights green)

· Error (flashes red)

1

  Insert the rechargeable battery into the charger slot.

If a rechargeable battery is facing the wrong way, the LED does not light.

2

  Charging state indicator LED lights red.

If a charging error occurs, the LED flashes red. If this happens, insert the rechargeable battery again.

3

  Charging is complete when the charging state indicator LED lights green.

Charging finishes within about 5.5 hours. Charging times vary depending on the charge remaining in the rechargeable batteries.

NOTICE

• Operating temperature is 10 to 30°C and storage temperature is 0 to 20°C.
• Remove the rechargeable batteries from the B60 if they will not be used for an extended period of time. If you leave the rechargeable 

batteries in the B60, while its power is turned off, for a long period of time, the rechargeable batteries will over discharge, which may 
drastically shorten their service lives or prevent them from recharging. If you will not be using the rechargeable batteries for a long 
time, store them without charging them, and then recharge them before you use them.

• They can be recharged about 300 times.

Summary of Contents for ATUC-50





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands