background image

16

Settings Menu

Processor Mode 

The LS28SE has the ability to assign unity 

gain (also called ‘pass through’) to one 

of the eight inputs available in the event 

it will be integrated into a system with 

a secondary control device, such as a 

surround sound processor. When an input 

is assigned as the processor input, the 

volume control on the LS28SE is disabled 

so that the processor’s volume is the only 

control used. 

To set up a processor input, connect 

the left and right output channels from 

your surround sound processor to the 

left and right inputs of your choice on 

the LS28SE. Press the ‘MENU’ button 

until ‘PROCESSOR MODE’ is displayed, 

and press ‘ENTER’. With ‘PROCESSOR’ 

displayed, turn the volume knob, or 

use the up/down volume buttons on 

the remote, to select the desired input 

for processor mode. Press the ‘ENTER’ 

button to select the input, and ‘ENTER’ 

once again to confirm the selection. The 

LS28SE will display ‘OKAY’ and show the 

selected input on the bottom line. 

When using the input selected for 

processor mode, note that in place of the 

volume number on the operation screen, 

a ‘pass through’ symbol will be shown. 

Warning 

When processor mode is assigned to an 

input, do NOT connect a source (such as 

a CD player or phono stage) to that input. 

This will send full output from the source 

to your amplifier(s), and could cause 

serious damage to your loudspeakers or 

amplifier(s) - not to mention your ears! 

Tube Hours 

The tube hours display shows the 

accumulated time the LS28SE has been 

powered on. This is useful for determining 

the number of usage hours of the installed 

vacuum tubes. See A Note about Vacuum 

Tubes on page 7 for specific information 

regarding the tubes in the LS28SE. To 

reset the tube hours counter, press the 

‘MENU’ button until ‘TUBE HOURS’ is 

shown. Press the ‘ENTER’ button to 

display ‘ENTER TO RESET’. Press ‘ENTER’ 

again and the display will read ‘ENTER TO 

CONFIRM’. A final press of the ‘ENTER’ 

button will reset the tube hour counter to 

0 and the display will show ‘OKAY’. 

Note 

Once the hour counter has been reset, 

the total accumulated hours cannot be 

recalled. 

Summary of Contents for ARCLS28SE























Reviews: