manualshive.com logo in svg

AuCom EMX3-0053B, User Manual, Page: 8 / 24

Share
Download
AuCom EMX3-0053B User Manual Download Page 8

USER MANUAL 

8   

 

Modbus TCP Interface (710-14812-00D) 

5.

 

PLC Configuration 

The PLC must be configured to map registers within the interface to addresses within 
the PLC.   

Example mapping of PLC registers to registers within the Modbus TCP Interface 

(Target): 

 

 

 

The device must be configured directly in the PLC. No additional files are required. 

 

 

6.

 

Feedback LEDs 

 

1

2

TX/

R

X 2

TX/

R

X 1

Li

nk

 2

Li

nk

 1

Err

or

Sta

tu

s

Po

w

er

14702.B

 

 

 

 

LED 
name 

LED 
Status 

Description 

Power  Off 

Device is not powered up. 

 

On 

Device is receiving power. 

Error 

Off 

No error. 

 

Flashing  System error. 

 

On 

Communication error. 

Status  Off 

Not ready. 

 

Slow flash  Ready but not configured. 

 

Fast flash  Configured and waiting for communication. 

 

On 

Communication has been established. 

Link x  Off 

No network connection. 

 

On 

Connected to a network. 

TX/RX x  Flashing  Establishing connection. 

 

On 

Operating normally. 

 

 

 

 
 

 

Summary of Contents for EMX3-0053B

























Reviews:

No comments