AUBER INSTRUMENTS
WWW.AUBERINS.COM
2019-05
P2/5
The user should decide the appropriate configuration for each output socket
based on the user’s particular application. Please refer to section 4.5 and
second 5 for details.
4.4 Change the Setpoints
The setpoint for temperature is
TSP
(
TSP
) and the setpoint for humidity is
HSP
(
HSP
). To access the setpoints, simply short-press the SET key, and
then the top window will show
TSP
and the bottom window will show its value.
Use UP or DOWN arrow keys to adjust the value, and short-press the SET key
again to save the new value and go to the
HSP
setting. The way to adjust and
save the setting is the same as for temperature setpoint. Once you press the
SET key again, the controller will return to its normal operation mode. Please
see Figure 2 for how to access the setpoints.
SET
Temp
50
.
5
72
.
0
RH
Temp
75
.
0
TSP
RH
Temp
40
.
0
HSP
RH
Short-press
Short-press
Short-press
Normal
Operating
Mode
Temperature
Setpoint
Humidity
Setpoint
SET
SET
Figure 2. How to access setpoints.
4.5 Adjust Parameters
Other control parameters are grouped into three sub-menus: temperature
(
tE
), humidity (
Hu
), and system (
SYS
)*. To access these parameters, long-
press SET key for 3 seconds, the top window will show
EDT
(
EDT
). Then use
UP or DOWN arrow key to select the sub-menu item (
tE
,
Hu
, or
SYS
) in the
bottom window, then press SET key again to confirm the selection. Please see
Figure 3 for how to access these parameters. The details for each parameter
are explained in section 5.
Temp
50
.
5
72
.
0
RH
Temp
TE
EDT
RH
Temp
SYS
EDT
RH
Temp
HU
EDT
RH
Temp
50
.
5
72
.
0
RH
SET
Long-press
3 seconds
SET
short-press
to confirm
SET
short-press
to confirm
SET
short-press
to confirm
Go through all parameters in
system menu
Go through all parameters in
temperature menu
Go through all parameters in
humidity menu
Normal Operating Mode
Normal Operating Mode
Figure 3. How to access parameter menus.
5.
Parameter Settings
All parameters are listed in Table 1. When a parameter is displayed in the top
window, its value is displayed in the bottom window. The user can use the UP
or DOWN arrow key to adjust the value in the bottom window, then press the
SEK key to save the new value and go to the next parameter. If no key is
pressed for 10 seconds, the controller will exit to its normal operating mode.
Table 1. Parameters.
Code
Description Setting
Range
Initi
al
No
te
Short-press SET Key
tSP
tSP
Temp. Setpoint
-40ºF ~ 176ºF
-40ºC ~ 80ºC
75.0 1
HSP
HSP
Humidity Setpoint
0 ~ 99.9% RH
40.0 1
Long-press SEK Key
Edt
EDT
Edit parameters
tE
: temperature menu
Hu
: humidity menu
SYS
*: system menu
tE 6
Temp. control settings (
tE
)
C-F
C-F
Temp. Unit
C
: Celsius
F
: Fahrenheit
F 7
tCM
tCM
Temp. Control Mode
Ht
: heating mode
CL
: cooling mode
CL 1
tdF
TDF
Temp. Control
Differential
0 ~ 50.0
3.0
1
toF
toF
Temp. Calibration
Offset
-10.0 ~ 10.0
0
2
tAH
TAH
Temp. High
Limit Alarm
-40ºF ~ 176ºF
-40ºC ~ 80ºC
95.0
3
tAL
TAL
Temp. Low
Limit Alarm
-40°F ~ 176ºF
-40°C ~ 80ºC
32.0
tAS
TAS
Temp. Anti-short
Cycle Delay (only for
cooling)
0 ~ 12 min
0
4
tSF
TSF
Temp. Sensor
Failure Operation
ON
: output energized
OFF
: output de-
energized
OFF 5
Humidity control settings (
Hu
)
HCM
HCM
Humidity Control
Mode
deH
: dehumidifying
H
: humidifying
H 1
HdF
HDF
Humidity Control
Differential
0% ~ 50.0%
3.0
%
1
HoF
HoF
Humidity Calibration
Offset
-10.0% ~ 10.0%
0%
2
HAH
HAH
Humidity High Limit
Alarm
0% ~ 99.9%
90.0
%
3
HAL
HAL
Humidity Low Limit
Alarm
0% ~ 99.9%
10.0
%
HAS
HAS
Humidity Anti-short
Cycle Delay (only for
dehumidifying)
0 ~ 12 min
0
4
HSF
HSF
Humidity Sensor
Failure
Operation
ON
: output energized
OFF
: output de-
energized
OFF 5
HdM
2
HDM
Humidity Output
Delay Mode
0, 1, 2
0 8
HdT
2
hdt
Humidity Delay
Timer
0 ~ 999 min
5 9
