manualshive.com logo in svg

ATX DigiStream Series, Hardware Interface Manual

Share
Download
ATX DigiStream Series Hardware Interface Manual Download Page 10

CHAPTER 2: CAPTURE CARDS

2-2 

VersAtive

®

Pro, DigiVu

®

 II, DigiStream – 1RU Hardware Interface Manual

2 .3   1 Channel - SDI 

Offered in:  

DigiVu II  

DVT1SDIIP

One input

• 

HD/SD SDI with embedded audio on BNC female jack.

2 .4   2 Channel - SDI

Offered in:  

DVT2SDIIP, DVT6SDIIP

Two inputs

• 

HD/SD SDI with embedded audio on BNC female jacks.

2 .5   4 Channel - SDI

Offered in:  

DVT4SDIIP, DVT6SDIIP

Four inputs:

• 

HD SDI with embedded audio on BNC female jacks (w/adapter cables).

1 Channel SDI Input Card

1

6

 

Not Used

Not Used

Not Used

SDI

1-Ch SDI Input Card Connections

2 Channel SDI Input Card

Not Used

Not Used

Not Used

HD SDI #1

HD SDI #2

2Ch SDI Input Card Connections

4 Channel SDI Input Card

4 Channel SDI Input Card With Adapter Cables

Not U

sed

Not U

sed

Not U

sed

Not U

sed

Not U

sed

HD SDI #1

HD SDI #2

HD SDI #3

HD SDI #4

4Ch-SDI Input Card Connections

Summary of Contents for DigiStream Series



































Reviews:

No comments

Brands by name

Popular brands

Load more brands