manualshive.com logo in svg

AtVideo 16CH AHD DVR, Instruction Manual

Share
Download
AtVideo 16CH AHD DVR Instruction Manual Download Page 51

 

51

3.5. Network Setup 

 With this menu, you can setup the network for DVR. Before starting this setup, the DVR must be 
connected to the router by LAN cable. Also, please make sure that internet is working properly.   
 
Important: If you are not familiar with network configuration and find any difficulties during this setup,   
please consult with your IT specialist or contact your distributor. 
 
You should complete your network setup to control and manage the DVR through the internet and/or 
local network just like you are next to the DVR. 
 
3.5.1. Connection 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

When No Router Is Used: 
 
1)  Static IP Mode: 

 - Internet Connection: Static IP ADSL, Leased Lines and LAN environments allow connection 
between the DVR and the remote user. 

 

- DVR Network Setting: Set the <Connection Mode> to <Static IP>. 

 
2)  Dynamic IP (DHCP) Mode: 

 - Internet Connection: Connect the DVR directly to a cable modem, DHCP ADSL Modem or FTTH 
network. 

 

- DVR Network Settings: Set the <Connection Mode> to <Dynamic IP> 

 
 

Summary of Contents for 16CH AHD DVR




























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands