3
ATTO Technology Inc. FastStream Installation and Operation Manual
1.1 ATTO FastStream NDMP 4600 characteristics
The ATTO FastStream NDMP 4600 is a 1-Gigabit Ethernet to SCSI 1U full-rack providing high
performance and cost effective backup and recovery for network-attached storage.
Dimensions
Width:
17 inches wide (42.95 cm)
Depth:
8.9 inches long (25.4 cm)
Height:
1.7 inches high: 1U (4.32 cm)
Weight:
approximately 8 pounds
Environment
Operating temperature:
Ambient air should not
exceed 40°C.
Airflow:
air enters through slots on the right of the
rear panel and exits through slots on the left of the rear
panel.
Humidity:
5-95% non-condensing
Power
Input voltage:
100-240VAC, 1.7-.7A, 50-60 Hz
Battery-backed event log:
A rechargeable Lithium
ion battery cell holds the event log memory for up to
30 days. If the FastStream NDMP 4600 has been
disconnected from power, recharging begins
automatically when power is restored to the system.
The battery is fully charged after 36 hours of
continuous power application.
WARNING
Risk of explosion if battery is removed
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
SCSI interface
The two independent SCSI ports on the FastStream
NDMP 4600 connect storage devices into the Ethernet
Storage Area Network (SAN). Each port is completely
independent from the other.
The ports are Ultra 320 busses with 68-pin VHDCI
connectors, 320 MB/sec. maximum throughput,
downward compatible with all forms of low voltage
differential and single-ended SCSI.
The FastStream NDMP 4600 supports all SCSI
devices including hard disk drives, tape drives, RAID
controllers and DVD, MO and CD libraries.
Ethernet interface
The four independent 100/1000 Ethernet RJ45 data
ports are labeled Ethernet ports 1, 2, 3 and 4. A
separate 10/100 Ethernet standard RJ45 management
port provides monitoring and management through
ATTO ExpressNAV, a browser-based interface.
Gb Ethernet cables must be at least CAT-5E certified.
Serial interface
The RS-232 serial port provides support for remote
monitoring and management through a command line
interface. It is set at the factory at 115,200 bps.
Reset switch
A reset switch on the back (connector) side allows
manual restart of the FastStream NDMP 4600 using a
small sharp implement inserted into the hole at the
back of the FastStream NDMP 4600.
LED indicators
LED indicators viewed from the front of the
FastStream NDMP 4600 (see Exhibit 1.1-1):
• Bicolor Ready/Fault: off means not ready; green
on shows ready, and yellow on means fault
• Power: indicates power has been applied.
• Each Ethernet data port has two LEDs: when the
speed LED is dark it indicates 100 Mb/sec.
speed; it lights yellow for 1000 Mb/sec. speed.
The activity LED lights green to represent an
active link, blinks to show activity and goes dark
when no link is present.
• SCSI activity is indicated for each port: lighted
green means activity; off shows no activity
LED indicators viewed from the connector (back) side
of the FastStream NDMP 4600 (see Exhibit 1.1-1):
• Bicolor Ready/Fault: off means not ready; green
on indicates ready, and yellow on shows fault
• Embedded in the RJ45 connector of the
management port: green on indicates a valid
link; off represents no link present
• Embedded in the RJ45 connector of the
management port: blinks yellow to indicate
management activity
Summary of Contents for FastStream NDMP 4600
