background image

8

the quartz sleeve, a mild acid may be used (i.e. vinegar).  Be certain to follow all recommended safety 

and handling procedures on the acid container.  It is important to 

 

handle the quartz sleeve with care to prevent breakage.  Make certain that all finger prints are wiped 

clean before reinstalling (see installation of the quartz sleeve).  Replace O-Rings [ATS8-544(2)] every 

time a quartz sleeve is cleaned or replaced. 

U.V. LAMPS:
INSTALLATION OF THE ULTRAVIOLET LAMPS:

CAUTION:  Never look directly at an operating U.V. lamp and never operate a U.V. lamp outside the 

  disinfection 

chamber.**DO NOT PUT POWER ON AT THIS TIME!**

Make sure unit is unplugged when installing or servicing ultraviolet lamp.  Remove any paper tabs on 

the U.V. lamp and avoid allowing fingerprints and other debris to deposit.  Carefully place the bulb 

inside the quartz sleeve leaving enough space to connect the socket connector to the lamp pins.  Slide 

the protective brass shrouds over the brass end nuts to secure the lamp is in place.

ULTRAVIOLET LAMP MAINTENANCE REQUIREMENTS:

The U.V. lamp is rated for 9,000 hours of continuous use.  After this period of time, the U.V. lamp has 

undergone a photochemical change.  While the lamp will not normally be burned out, the lamp quartz 

may no longer emit the 254-nm shortwave U.V. to effectively kill bacteria.  Failure to replace the U.V. 

lamps every 9,000 hours may cause bacteriological breakthrough.  Should the use of the disinfec-

tion unit be intermittent, in no case should the U.V. lamp be used for more than 24 months regardless 

of the number of hours of operation due to normal shelf life degradation of the U.V. bulb.  Changing 

the quartz sleeve should be done at the same time U.V. lamp replacement is scheduled.   

Also replace O-Rings.

Check  with the dealer that installed your system, or aquat.com to find the distributor in your 

area for replacement parts.

It is recommended that your water supply be tested periodically (yearly) through your local health 

department or approved certified laboratory.

ELECTRICAL:

The DWS C Series are  furnished with 6' line cord that will plug into a 115V outlet.  Electrical recep-

tacles must be properly grounded for safe operation.  Improper grounding will void any warranty.

When possible use a separate breaker to minimize voltage fluctuations and avoid accidental shut off.  

After unit is installed and water is turned on, plug the unit into 115V wall receptacle.

NOTE: Avoid exposing your eyes to U.V. light.

Summary of Contents for DWS-8C
























Reviews: