![background image](http://html1.mh-extra.com/html/imi/norgren-f64b-series/norgren-f64b-series_installation-and-maintenance-instructions_2047487001.webp)
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document. (1999-xxxxb) © 2020 IMI International s.r.o.
05/21
IM/en 8.240.115.001
Technical Data
Fluid: Compressed air
Metal bowl: 17 bar (250 psig)
Transparent bowl: 10 bar (150 psig
Operating temperature*:
Metal bowl: –20° ... +65°C (0° ... +150°F)
Transparent bowl: –20° ... +50°C (0° ... +125°F)
* Air supply must be dry enough to avoid ice forma-
tion at temperatures below +2°C (+35°F).
Integral F64B/L Pre-filter Element: 40 µm
nominal
Particle Removal F64B/L: 0,01 µm
Maximum Remaining Oil Content:
0,003 mg/m3 at +21°C (+70°F)
Air Quality: Within ISO8573-1:2010: 1:7:0
Typical performance characteristics
Inlet pressure
(bar)
Maximum flow (dm
3
/s) *
F64B
F64L
1
6,7
7,1
3
10,7
11,3
5
13,8
14,4
6,3
15,6
16,3
7
16,5
17,2
9
18,8
19,5
* Maximum flow to maintain stated oil removal
performance.
Automatic drain connection: 1/8”
Automatic drain operating conditions:
Bowl pressure required to close drain:
Greater than 0,3 bar (5 psig)
Bowl pressure required to open drain:
Less than 0,2 bar (3 psig)
Minimum air flow required to close drain:
1 dm3/s (2 scfm)
Manual operation: Depress pin inside drain
outlet to drain bowl
Nominal bowl size: 0,2 litre (7 fluid oz)
Materials:
Body: Zinc
Bowl:
Metal: Zinc
Transparent: Polycarbonate
Metal bowl sight glass, standard: Pyrex
Element: Composite materials
Elastomers: Synthetic rubber
Replacement Items
Service Kit
(Item No. (s) 3, 5, 8, 9, 14, 16, 17, 18, 20):
F64B-
F64B-KITA0V
F64L- F64L-KITA0V
Pyrex sight glass kit (Item No. 7)
2273-97
Element, coalescing (Item No. 3):
F64B
5350-99
F64L
5350-98
Element, integral pre-filter
(Item No. 16)
3698-02
Activated carbon pack
(Item No. 18)
5568-02
Manual drain (Item No. 9, 12, 13, 14) 684-84
Automatic drain (Item No. 8)
6000-70
Automatic drain - USA only
(Item No. 8)
3000-70
Operation
On exceptionally dirty lines it may be neces-
sary to clean the pre-filter element at 90 day
intervals.
Do not exceed Maximum Flow rating or
excessive pressure drop will result or oil carry
over may occur.
The top filter element acts as absorbant
pack to remove any small traces of oil or
hydro-carbon gases which might
be carried over from the lower bowl.
These elements also provide protection in the
event of any failure of the lower filter.
Resistance to air flow will gradually increase
as the filter element collects solid particles.
The pressure differential across the element
should not be allowed to exceed 0,7 bar
(10 psi) or damage to the element may
occur.
Servicing
Air Service equipment should be initially
maintained annually. Use, quality of air and
condition at examination may indicate ad-
justment of the maintenance interval.
1. Open manual drain to expel accumulated
liquids. Keep liquids below element (3).
2. To operate automatic drain manually, lift
operating pin in bottom outlet with a blunt
rod.
3. Clean or replace filter element when dirty.
Option selector
Port
2 1/4“
3 3/8“
4 1/2“
6 3/4“
N No yoke
Drain
A Automatic
M Manual
Bowl
R Metal with Pyrex sight glass
T Transparent
Thread
A
PTF
B
ISO Rc tapered
G ISO G parallel
N
No yoke
F64
˙
–
˙˙N
–
˙˙0
Bowl
B Coalescing &
activated carbon element
L
Extended coalescing &
activated carbon element
8
9
18
18
21
15
15
17
20
16
19
3
3
1
1
10
9
10
5
5
12
14
13
14
20
16
6
19
3
3
9
5
12
14
10
13
10
8
9
5
14
4
14
21
28
37
17
4
2
2
7
7
F64B, F64L - Ultra High Efficiency Coalescing Filter
Installation & Maintenance Instructions