ATON AH66T Installation Manual Download Page 76

Page: 76 / 90

A T O N

AH66T

INSTALLATION MANUAL

ATON 2010

Page 75

Digit Selection

Description: Sends digits for direct tuning. Has a 5 second timeout.

Example:

&AH66,R1,DIGIT,1<cr>

Selects DIGIT (DIGIT) ONE (1) for CHASSIS ONE’S (R1)

tuner.

&AH66,R1,DIGIT,0<cr>

Selects DIGIT (DIGIT) ZERO (0) for CHASSIS ONE’S (R1)
tuner.

&AH66,R1,DIGIT,5<cr>

Selects DIGIT (DIGIT) FIVE (5) for CHASSIS ONE’S (R1)

tuner.

&AH66,R1,DIGIT,1<cr>

Selects DIGIT (DIGIT) ONE (1) for CHASSIS ONE’S (R1)

tuner.

Results:

Tunes Chassis One’s Radio to 105.1.

Enter Command

Description: Sends the enter command.

Examples:

&AH66,R1,ENTER<cr>

Sends the ENTER (ENTER) command to CHASSIS ONE’S

(R1) tuner.

&AH66,R2,ENTER<cr>

Sends the ENTER (ENTER) command to CHASSIS TWO’S

(R2) tuner.

Results:

Processes the previous command.

Prefix

Parameter 1

Parameter 2

Digit

&AH66

R1/R2

DIGIT

0-9

Prefix

Parameter 1

&AH66

R1/R2

ENTER

Summary of Contents for AH66T






















































































Search results

Summary of Contents for AH66T

Reviews:

Brands by name

Popular brands

ATON AH66T, Installation Manual

Search results

Summary of Contents for AH66T

Reviews:

Brands by name

Popular brands