background image

6

ATOMIKRC.COM

18010

Controller Introduction Cont.

End Point Adjustments (EPA)

Trim Adjustments

Functions

Use the ST/R and ST/L knobs when performing left and right steering angle extent adjustments. Increasing 

the value will allow the rudder to turn further while decreasing the value will lessen travel of the rudder. 

Too high of a value will make the boat uncontrollable while to low of a value will greatly increase the 

turning radius.

Settings

   1. Steering (right side) adjustment

       Rotate “ST/R” knob to the left end points means minimum value 0%, right end point means maximum 

value 100%.

   2. Steering (left side) adjustment

       Rotate “ST/L” knob to the left endpoint means minimum value 0%, right end point means maximum 

value 100%.

Steering Trim: Adjust “ST/TRIM” “R/L” so that the rudder is centered prior to operation, you may also adjust 

this control to make the boat run straight during operation.

Throttle Trim: Adjust “TH/TRIM”  “B/F” so that the propeller does not turn while the throttle trigger is in the 

neutral position.

Pre Run Checklist

1. Inspect the prop for any damage. If any damage is noted, replace prop immediately.
2. Inspect the boat for loose screws and nuts. RC boats experience high frequency vibrations and as a result 

screws, nuts, and bolts will become loose.

3. Inspect water cooling lines for cracks, clogging, or other signs of wear.
4. Install the battery making sure it is fully charged.
5. Turn the controller on and perform a radio check from 100 feet away to be sure the radio system is 

functioning properly. Weak controller batteries may also reduce radio range.

6. Be sure to properly secure the seal and hatch cover before launching the boat.
7. Make sure the area is clear of people, solid objects and animals before launching the boat.

IMPORTANT

 - Prior to each and every use it is very important to perform the Pre Run Checklist. This will 

help to ensure safe and enjoyable operation. 

Steering Switch Reverse

Throttle Trim Backwards

Throttle Trim Forwards

Power Indicator

Steering Switch Normal

Steering Trim Right

Steering Trim Left

Steering Travel Angle Left

Steering Travel Angle Right

REV

POWER

NOR

ST

barb

WIRE

barb

WIRE

Summary of Contents for 18010

















Reviews: