Atmos A45 Operation And Maintenance Manual Download Page 52

Page: 52 / 64

www.atmos.cz

52-GB

Operation and Maintenance Manual - GB

ALARM
SENSOR TK

Failure of the boiler tempera-

ture sensor TK in the boiler or
in the middle part of buffer tank
– the sensor is short-circuited
(damaged) or disconnected

Check the connection of the

sensor in the burner

Check the cable and sensor

for damage

Repair or replace

ALARM
SENSOR TSV

Failure of the waste gas or so-

lar sensor TSV – the sensor is
short-circuited (damaged) or
disconnected

Check the connection of the

sensor in the burner

Check the cable and sensor

for damage

Repair or replace

ALARM
VENTILATOR

Failure of the fan or fan speed

sensor

Check the cable of the speed

sensor and its connectors

Check whether the fan does

not size, it must be possible to
turn it easily by hand

Check the fuse on the electron-

ic board for the fan (1.0 A)

Repair or replace

ALARM
VENT 2

the same as

ALARM

VENTILATOR

Failure of the exhaust blower

of the boiler or defective ca-
pacitor under the hood of the
boiler

the same as

ALARM

VENTILATOR
Change the starting capacitor

for the exhaust fan

Change the exhaust fan of the

boiler.

ALARM RELE

Error at the output for the ex-

ternal conveyor (neither out-
put is functional)

The external conveyor does

not feed fuel to the burner

Check and if necessary re-

place the fuse for the convey-
or (0.8 A)

Check the wiring between

electronic board and socket

Broken gearbox of the con-

veyor or output for conveyor
control

If you are not using the re-

serve,  reconnect  the  convey-
or  terminals  to  the  reserve
and  set  the  parameter  S6  =
7.  If  you  use  the  reserve  for
other  applications,  replace
the electronic control unit.

Summary of Contents for A45

































































Search results

Summary of Contents for A45

Reviews:

Related manuals for A45

Brands by name

Popular brands

Atmos A45, Operation And Maintenance Manual

Search results

Summary of Contents for A45

Reviews:

Related manuals for A45

Brands by name

Popular brands