background image

LIMITED WARRANTY

Atmor warrants to the original owner that our instant water heaters will be free from defects 

in workmanship and material for  a period of TWO YEARS from the date of purchase, and 

free  from  leakage  for  a  period  of  SEVEN  YEARS  from  the  date  of  purchase.  Should  any 

part(s)  prove  to  be  defective  during  this  period, Atmor  will  be  responsible  for  replacement 

of the defective part(s) only. Atmor is not responsible for labor charges or any incidental or 

consequential expenses.

Should  the  owner  wish  to  return  the  water  heater  for  repair,  the  owner  must  first  secure  a 

written authorization from Atmor. The owner shall be required to show proof of purchase date 

and to pay all transportation costs to return the defective part(s) or water heater for repair or 

replacement. Warranty is void if: (i) water heater has been installed or used improperly; (ii) 

design has been altered in any way; (iii) water heater has been installed and/or serviced by 

someone other than a licensed electrician ; (iv) or if the water heater has been installed or used 

in contradiction to installation instructions, applicable laws and/or ordinances.

Distributed by:

PARAGON GROUP USA LLC

15 Engle Street, 3

rd

 Floor

Englewood, NJ 07631
1-888-783-6082

P.N. 1

15045C

Summary of Contents for AT900-03













Reviews: