background image

Section 1 
Introduction 

The ATMEL PCMCIA Fast-VNET-R (5V)    based on ATMEL AT76C502A Wireless Media Access 
Controller is a network card with a rate of 1, 2, 5.5, and 11 Mbps operating in the ISM 
band using Direct Sequence Spread Spectrum (DSSS) transmission implementing the 
IEEE 802.11b standard. For this card ATMEL currently provides Device Drivers for MS 
Windows

® 

98/2000, and Windows

® 

Me. ATMEL also provides tools for the configuration 

and firmware upgrade of the cards. These tools, as well as the installation procedure for 
the MS Windows 98/2000, and Windows Me operating systems are described in this 
document. 
To install the adapter and operate under an operating system two pieces of software are 
needed. The first one is the driver, which provides the necessary mechanisms to the 
operating system in order to use the adapter as any other networking adapter. The 
driver communicates with the firmware using exchange of commands (Set MIB, Get 
MIB, Scan, Sync, etc.). The other piece of software needed is the code written on the 
MAC chip, which is responsible for the interface with the driver, and for the implementation 
of the IEEE 802.11b functions. 

1.1 Package 
Contents 

Please make sure that your received the following with your AT76C502A-Evaluation Kit: 
• One (1)    PCMCIA Fast-VNET-R (5V) card 
• User Guide 
• Firmware, Drivers, and Software Tools CD 

1.2 System 
Requirements 

• Operating System: MS Windows 98/2000, Windows Me with Service Pack 4 or later 
• Desktop PC or notebook PC with CD-ROM drive 

1.3 AT76C502A 
Features 

AT76C502A based Fast-VNET adapters offer compliance with the IEEE 802.11b specification. 
This feature allows them to communicate with wireless devices from other 
manufacturers that support the standard. Among the features of the AT76C502A WLAN 
MAC controller are the following: 

– Wireless interface following the IEEE 802.11b standard supporting DSSS 2.4 GHz 
wireless PHY 
– Wireless LAN MAC Unit with ARM7TDMI RISC processor 
– Integrated 128-byte transmit and 128-byte receive FIFOs, for wireless MAC layer 
functions

 

– 16-bit PCMCIA bus interface 
– Glueless SRAM interface for all MAC operations, supporting up to 16 MB of external 
memory 
– Integrated 6Kx32 bit internal SRAM, used for fast program code execution and 
temporary storage of data 
– Glueless Flash memory interface, supporting up to 16 MB on non volatile memory 
for permanent storage of program code 
– Enciphering/deciphering of wireless data by the implementation of the WEP 
algorithm 
– Supports 11, 5.5, 2, and 1 Mbps rates 

 
 
 
1.4 Firmware 
Features 

Summary of Contents for AT76C502A





















Reviews: