22
atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Each command or feedback is terminated with a carriage return.
Note:
If the command fails or is incorrect the feedback should be “Command FAILED”
To help with zone troubleshooting the matrix will broadcast “#*PORTXX_[feedback]” when
receiving any feedback from any zone.
RS-232 & TCP/IP Control Commands
The command codes are case sensitive, do not change capitalization, spacing, or lettering.
Command
Feedback
Description
PWON
PWON
Power on
PWOFF
PWOFF
Power off
PWSTA
PWx
Will display the power status of the matrix
e.g.
Power is on, feedback will be PWON
Version
Firmware #
Brings up the current firmware version
Type
Model #
Brings up the model information
Lock
Lock
Locks the front panel of the matrix so no buttons are active
Unlock
Unlock
Unlocks the front panel of the matrix, enabling the buttons again
All#
x1AVx1,x2AVx2,...
Resets all inputs to corresponding outputs
e.g.
input 1 to output 1, input 2 to output 2, input 3 to output 3, etc
x1$ Y
x1$ Y
Changes status of output channel Y= on/off/sta
e.g.
to turn off output 3 = x3$ off
x1All
x1All
Sets selected input to all outputs
e.g.
x3All would set input 3 to all outputs
x1AVx2
e.g.
x3AVx7
x1AVx2
e.g.
x3AVx7
Switch input to output
e.g.
input 3 to output 7
x1AVx2,x3,x4
e.g.
x3AVx1,x4
x1AVx2,x3,x4
e.g.
x3AVx1,x4
Switch input to multiple outputs
e.g.
Switch input 3 to output 1 and 4
MirrorHdmiX OutY
MirrorHdmiX OutY
Mirror the HDMI output port with an HDBaseT output port
X= HDMI port Y= HDBaseT Output, sta
e.g.
Mirror HDMI 6 with Output 1: MirrorHdmi6 Out1
UnMirrorX
e.g.
UnMirror6
UnMirrorX
e.g.
UnMirror6
Removes the chosen HDMI port from mirror mode
e.g.
Unmirror HDMI 6 and no longer follows an HDBaseT output
VOUT
X
+
e.g.
VOUT2 +
VOUT
X
(YY)
e.g.
VOUT2 (-70)
Turns the volume of the chosen output (
X
) up one step
e.g.
Turn the volume up from level -71dB to -70dB on analog output 2
VOUT
X
-
e.g.
VOUT3 -
VOUT
X
(YY)
e.g.
VOUT3 (12)
Turns the volume of the chosen output (
X
) down one step
e.g.
Turn the volume down from level 13dB to 12dB on analog output 3
VOUT
X
(YY)
e.g.
VOUT1 (-50)
VOUT
X
(YY)
e.g.
VOUT1 (-50)
Set the volume of the chosen output (
X
) to a specific (YY) level
e.g.
Set the volume to -50dB on output 1
VOUT
X
sta
VOUT
X
(YY)
Displays the current volume level of the chosen output (
X
)
VOUTMute
X
Y
e.g.
VOUTMute2 on
VOUTMute
X
Y
e.g.
VOUTMute2 on
Mute the volume level of the chosen analog output Y=on,off,sta
e.g.
Mute the volume of analog output 2
IROFF
IROFF
Disables the front panel IR receiver window
IRON
IRON
Enables the front panel IR receiver window
Statusx1
x7AVx1
Shows what input is connected to selected output
Status
x1AVx1,x2AVx2,
x3AVx4, ....
Displays which inputs are currently connected to which outputs
Save
Y
e.g.
Save2
Save
Y
e.g.
Save2
Saves I/O route settings for future use, preset options 0 to 8
Recall
Y
e.g.
Recall2
Recall
Y
e.g.
Recall2
Recalls saved I/O route settings for the chosen preset number
Clear
Y
e.g.
Clear2
Clear
Y
e.g.
Clear2
Erases the saved I/O route settings for the chosen preset number
Mreset
Mreset
Sets matrix back to the default settings
RS232zoneX[command]
e.g.
RS232zone1[PWRO]
RS232zoneX[command]
e.g.
RS232zone1[PWRO]
Send commands to devices connected to the receiver RS-232 ports.
Commands are the same as the ones stated in this table. X = zone #
e.g.
Turning the power on for the device connected in zone 1
