manualshive.com logo in svg

Atlona AT-HDR-M2C, User Manual

Share
Download
Atlona AT-HDR-M2C User Manual Download Page 17

AT-HDR-M2C

17

The Web GUI

A/V Settings page

The 

A/V Settings

 page is divided into two sections:  

Video

 and 

Audio

.  The 

Video

 section allows the preferred 

input timing to be selected as well as whether or not HDCP content is allowed to pass.  The 

Audio

 section provides 

options to control the output audio volume, muting, treble, and bass.

Prefer Timing (HDMI)

 

Click this drop-down list to select the desired input. 

 

 

 

 

 

 

 

 

 

Input HDCP

 

Click this toggle to report HDCP compliance or non-compliance to the source device.

 

•  ON 

- Reports to the source device that the AT-HDR-M2C is an HDCP-compliant sink.

•  OFF 

- Reports to the source device that the AT-HDR-M2C is a non-HDCP-compliant sink.

 

Video

Available Resolutions

800x600

1280x800

1920x1080

3840x2160@30Hz

1024x768

1366x768

1920x1200

3840x2160@60Hz

1280x720

1600x900

2560x1440

Audio Info

Audio Format

 

The audio format detected on the input.

Sampling Rate

 

The sampling rate of the input audio signal, expressed in kilohertz (kHz).

Channels

 

The number of audio channels detected on the input signal.

Summary of Contents for AT-HDR-M2C







































Reviews:

No comments

Brands by name

Popular brands

Load more brands