atlona-asia.com.cn
9
Panel Description
Front Panel
4 5
c d
1
2
3
4
5
POWER
ENTER
6
7
8
9
0
6
FNC
CANCEL
EDID
INFO
AT-UHD-PRO3-1616M
1
2 3
a
b
1. IR Receiver Window - Receives the signal from the included IR hand held remote control or 3rd
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 19 20
party controller
HDMIIN
HDMIOUT
AUDIOOUT MAIN ON
L 1 R L 2 R L 9 R RS-232
IRIN
2. Function
(FNC)
Button - Select for command options
(blue backlight when selected)
a.
EDID:
Save/Load EDIDs to individual inputs
b.
INFO:
Displays the firmware, IP, and MAC address
c.
1:
Save a single input to all the outputs with this function
d.
2:
View additional matrix and zone output RS-232 baud settings
3. Cancel Button - Within the function menu use this button to go back one screen or to return to
the home screen
Note:
You cannot power off or change functions unless you return to the home screen
4. Power Button - Cycles the power between On
(blue backlight)
or Standby
(red backlight)
mode
5. Enter Button - Use to view current status for inputs and outputs or to confirm a command
6. Number buttons - Use these buttons to select input and output paths or use with the function
button to change matrix settings
atlona.com
4
Toll free: 1-877-536-3976
Local: 1-408-962-0515
1
2
3
4
5
POWER
ENTER
6
7
8
9
0
FNC
CANCEL
EDID
INFO
Back Panel
AT-UHD-PRO3-1616M
1
2
3
4
11
MAIN
RS-232 IRIN
RX TX
15
5
6
10
7
8
9
1. Long distance HDBaseT ports - Connect to long distance EX receivers for pass through
of PoE, control, and A/V signals.
Ex.
AT-UHD-EX-70C-RX
2. Extended distance HDBaseT ports - Connect to extended distance EX receivers for pass through
of PoE, control, and A/V signals.
Ex.
AT-UHD-EX-100CE-RX
3. HDMI Input - Connect HDMI sources to these ports
Ex.
DVD players, Blu-ray players, computers, game consoles, etc
4. Audio out - Captive screw analog audio breakouts for use with a sound system or multi-channel
zone amplifier
5. IR IN - Use with a 3rd party IR control box to extend IR control commands to video displays over
category cable
6. IR OUT - Connect IR emitter here for controlling sources
7. LAN port - Connect to a network for TCP/IP, WebGUI, and firmware updates
8. FW port - USB not enabled at this time for future functionality
9. Main system control - Connect IR or RS-232 control system to the matrix
10. Internal power supply - Connect included IEC C13 power cable from here to a power outlet.
11. HDMI outputs - Mirror to provide a local output for HD audio routing to an AVR, or matrix the
ports to provide a local video output for in room displays or an HDBaseT extender set
Ex.
AT-UHD-EX-100CE-KIT or AT-UHD-EX-70C-KIT
Rack Mounting
atlona.com
5
To rack mount the UHD-PRO3-1616M
unit: use the rack mount ears, the 6
screws from the sides of the UHD-
PRO3-1616M, and 4 rack screws.
To affix the rack mount ears, remove
the three screws on each side of the
UHD-PRO3-1616M and affix the rack
ears to the UHD-PRO3-1616M
(as
shown in the picture to the left)
.
Place the UHD-PRO3-1616M in the
rack, lining the holes in the rack ears
with the holes in the rack. Once
placed, use the rack screws to keep
the unit in place.
(as shown in the picture
to the left)
Note:
Increase the air flow as needed to
maintain the recommended
temperature inside the rack.
Note:
Do not exceed maximum weight loads
for the rack. Install heavier equipment
in the lower part of the rack for
stability.
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Category Cable
For the category cables used in the installation of these products, please be sure to use a 568B
termination as pictured below:
1. White - Orange
2. Orange
3. White - Green
4. Blue
5. White - Blue
6. Green
7. White - Brown
8. Brown
Use the table below to verify the best category cable for the installation.
Important!
4K (UHD) signals are sensitive to cable quality and installation technique. It is recommended to
use CAT6a/7 solid core cables for best results.
Note:
For cable distances see the specifications on page 26
Connector
Connector type and size is very important to ensure extenders work correctly. Please use the
matching cable type with the correct RJ45 connector.
CAT5e and CAT6 cables should use only CAT5e RJ45 connectors
CAT6a cables should use only CAT6a connectors
CAT7 cables should use only CAT7 connectors
Using the wrong size of connectors may result in interference causing loss of signal.
Important!
"EZ RJ45 connectors" are not recommended with HDBaseT extenders. Doing so may result in
stray EMI/RFI signals to be picked up and interfere with audio and video transmission.
atlona-asia.com.cn
4
