Atlas SunCool CPS+ Operating Manual Download Page 19

Page: 19 / 36

- 19 -

Operating Manual SunCool for SUNTEST

CPS+

6.2 Starting for the first time

NOTE – starting for the first time

The instrument may only be started for the first time by
an Atlas technical service representative or authorized
Atlas service provider.

6.3 Checking the instrument

components

SunCool start up

WARNING – electrical shock!

Touching live parts can lead to life threaten-
ing electrical shocks. Disconnect the device
from the power supply before testing!

• Pull the main power supply plug out of the

receptacle and secure against reconnecting

• Check whether the instrument is voltage

free

Only instrument parts which are in perfect condition
ensure the functional reliability of the SunCool and the
SUNTEST

CPS+ device. Check the instrument compo-

nents and parts listed below for damage and operation
before starting or before every new test run. Damaged
or worn parts should not be used.

Checklist:

The following parts must be checked before starting:
•   Seat and tightness of the quick-release coupling
•   Condition of the coolant lines
•   Condition of plugs and power cables

Summary of Contents for SunCool CPS+





































Search results

Summary of Contents for SunCool CPS+

Reviews:

Related manuals for SunCool CPS+

Brands by name

Popular brands

Atlas SunCool CPS+, Operating Manual

Search results

Summary of Contents for SunCool CPS+

Reviews:

Related manuals for SunCool CPS+

Brands by name

Popular brands