Atlanta Attachment Company 4300B Technical Manual & Parts Lists Download

Page: 51 / 136

Technical Manual & Parts Lists

3.3.- Electrical

All maintenance should be performed by a qualified service technician.

3.3.1.- Main Power witch

The main power On/Off switch is on the back of the machine. It is used to turn the

power on to the whole machine. This machine requires 220V Single Phase 15

Amps. If you have problems with the power not coming on when the On button is

pressed you may check this switch by doing the following.

ATTENTION. Make sure that the machine is unplugged before proceeding and that all lock

out/tag out procedures have been correctly followed (See to Lockout tag out procedure)



Check the circuit breakers if

any of the barkers had gotten

overloaded at some point.



Replace the cover, plug the

machine in, and try turning the

machine back on.



If the contact still trips the

overload, then there is a

problem either with the wiring

or the contactor.



Use the wiring diagram for

your machine in the parts

manual to check the voltages.



Try replacing the circuit

breaker.

Summary of Contents for 4300B









































































































































Search results

Summary of Contents for 4300B

Reviews:

Related manuals for 4300B

Brands by name

Popular brands

Atlanta Attachment Company 4300B, Technical Manual & Parts Lists

Search results

Summary of Contents for 4300B

Reviews:

Related manuals for 4300B

Brands by name

Popular brands