background image

Contacting Environmental Technology, Inc.

 

For assistance, contact Customer Service. Office hours are from 8:00 AM until 5:00 PM ET.

 

Voice  (800) 234-4239 (USA and Canada) or (574) 233-1202 (elsewhere)

 

Fax 

(888) 234-4238 (USA and Canada) or (574) 233-2152 (elsewhere)

 

E-mail [email protected] 

 

Mail 

Environmental Technology, Inc.

 

 

1850 North Sheridan Street

 

 

South Bend, IN 46628

RETURNS AND REPLACEMENT PART PURCHASES

Equipment cannot be returned for credit once it has been installed. Environmental Technology, Inc. will repair or replace faulty 
equipment under warranty. Prior to removal of equipment for warranty return, please contact Environmental Technology, Inc. 
Technical Support at 800.234.4239 for troubleshooting assistance.

Before returning a unit to Environmental Technology, Inc., obtain a Return Merchandise Authorization from our Customer 
Service Department, available between 8:00 a.m. and 5:00 p.m. Eastern Time at 574.233.1202 or 800.234.4239. If possible, 
use the original container and packing materials when packing the unit for shipment. It is important to mark the Return 
Merchandise Authorization clearly on the outside of the shipping container so that it may be correctly processed upon receipt at 
Environmental Technology. For more information about replacement parts or for a replacement Data Sheet or Manual, please 
visit www.networketi.com.

LIMITED WARRANTY

ETI’s two year limited warranty covering defects in workmanship and materials applies. Contact Customer Service for complete 
warranty information.

DISCLAIMER

Environmental Technology, Inc. makes no representations or warranties, either expressed or implied, with respect to the contents 
of this publication or the products that it describes, and specifically disclaims any implied warranties of merchantability or 
fitness for any particular purpose. Environmental Technology, Inc. reserves the right to revise this publication, and to make 
changes and improvements to the products described in this publication, without the obligation of Environmental Technology, 
Inc. to notify any person or organization of such revisions, changes or improvements.

The ETI logo, We Manage Heat, CIT, GIT, and SIT are registered trademarks of Environmental Technology, Inc. EUR and RCU are trademarks 
of Environmental Technology, Inc. Copyright ©  2017 Environmental Technology, Inc. All rights reserved. Printed in USA.

Summary of Contents for TRACON FPT 130














Reviews: