ATI Technologies Flexdeburr 9150-RC-300 Series, Installation And Operation Manual, Page: 15 / 38

Flexdeburr Installation and Operation Manual
Document: 9610-50-1007-11
Pinnacle Park
•
1031 Goodworth Drive
•
Apex, NC 27539
•
Tel: 919.772.0115
•
Fax: 919.772.8259
•
www.ati-ia.com
•
Email: info@ati-ia.com
15
3. Technical Description
3.1 Product Description
Attached at the end of this document you will find the RC deburring tool product description.
3.2 Technical Specifications
Main specifications for the RC deburring tools:
Parameter Rating
Motor Air Turbine
Idle Speed (RPM) RC-300 Series: 30,000
RC-340 Series: 40,000
RC-660 Series: 40,000
Torque (Max.) RC-300 Series: 0.09 N-m (0.8 lb-in)
RC-340 Series: 0.08 N-m (0.7 lb-in)
RC-660 Series: 0.16 N-m (1.4 lb-in)
Power RC-300 Series: 300 Watts (0.40 hp) @ 30,000 RPM
RC-340 Series: 340 Watts (0.46 hp) @ 40,000 RPM
RC-660 Series: 660 Watts (0.88 hp) @ 40,000 RPM
Weight (without Adapters) RC-300 Series: 1.2 kg (2.6 lb)
RC-340 Series: 1.2 kg (2.6 lb)
RC-660 Series: 2.2 kg (4.9 lb)
Compensation (Radial) RC-300 Series: +/- 7.5mm max., +/- 3mm recommended
RC-340 Series: +/- 7.5mm max., +/- 3mm recommended
RC-660 Series: +/- 9mm max., +/- 4.5mm recommended
Compliance Force RC-300 Series: 12.7-42 N (2.8–9.5 lb) @ 1.0-4.1 bar (15–60 psi)
(Measured at Collet) RC-340 Series: 12.7-42 N (2.8–9.5 lb) @ 1.0-4.1 bar (15–60 psi)
RC-660 Series: 12.8-45.4 N (2.8–10.2 lb) @ 1.0-4.1 bar (15–60
psi)
Burr Surface Speed Dependent on cutter geometry and motor
Spindle Air Pressure 6.2-6.5 bar (90–95 psi) (All Models) [6.9 bar (100 psi) max]
Air Consumption (Idle) RC-300 Series: 2.8 l/s (6 CFM)
RC-340 Series: 2.8 l/s (6 CFM)
RC-660 Series: 5.4 l/s (11.5 CFM)
Air Consumption (Stall) RC-300 Series: 10.2 l/s (21.5 CFM)
RC-340 Series: 10.2 l/s (21.5 CFM)
RC-660 Series: 17.9 l/s (38 CFM)
Sound Pressure Level Less than 70 dB(A) (All Models, without Cutter)
Collet Size (Standard)** 1/4" (All Models), -E Models Supplied with 6mm Collets
Rotary Burrs
++
Commercial Units Rated 40,000 RPM or Higher
Special Tools Open End Wrenches (1 Pair Supplied)
9/16" (14.5mm), 7/16" (11mm)
10mm Narrow (Only for use with ER11 Collets, -ER Models)
Specifications applied to a series of models cover the basic “inch” designs, metric -E models, and
-ER models with the ER-11 collet system.
** Optional Sizes Available, See Section 6
++
ATI Can Supply Burrs, See Section 7.2