ATI Corporation Preseeder 365 Operator'S Manual Download Page 24 | Manualshive

Page: 24 / 29

background image

18

MAIN DRIVE BELT REMOVAL

1. Turn off tractor engine and lower tiller

onto level ground.

2. Remove Main Drive Belt Shield (See

Figure 30).

3. Move the Drive Belt Release Handle to

the disengaged position (See Figure 31).

4. Remove the belt from the pulleys in the

following order (See Figure 32).

A. Adjustable Idler Pulley

B. Gearbox Pulley

C. Tension Idler Pulley

D. Drive Pulley

Reverse order to reinstall the belt.

MAIN DRIVE BELT ADJUSTMENT

When the Drive Belt Release Handle is in the
engaged position the spring should be approxi-
mately 1" longer the in the released position. If
due to belt wear or replacement, the spring
length varies by more then 1/2" adjustment is
required.

1. Turn off tractor engine and lower tiller

onto level ground.

2. Remove Main Drive Belt Shield (See

Figure 30).

3. Move the Drive Belt Release Handle to

the disengaged position.

4. Loosen the bolt in the center of the

Adjustable Idler Pulley (A).

MAINTENANCE

FIGURE 30 Main Drive Belt Shield

FIGURE 32 Main Drive Belt Removal - Pulley Locations

FIGURE 31 Main Drive Belt Release Handle

«
...
22
23
24
25
26
...
»

Summary of Contents for Preseeder 365






























Reviews:

No comments

Related manuals for Preseeder 365

Brand: York Pages: 4

Brand: Partner Pages: 60

Brand: York Pages: 78

Brand: Poulan Pro Pages: 40

Brand: AL-KO Pages: 112

WSAT-SC 100D Series

Brand: CLIVET Pages: 50

Brand: Carel Pages: 2

Brand: AEG Pages: 60

Brand: Sumo Quatro Pages: 11

Brand: Westfalia Pages: 40

Touch Pilot Control Series

Brand: Carrier Pages: 36

TOUCHPILOT 30KAV

Brand: Carrier Pages: 44

Brand: Draper Pages: 13

Brand: Draper Pages: 24

Sunjoe Tiller Joe TJ604E

Brand: SNOWJOE Pages: 16

Brand: Elkay Pages: 2

Brand: Elkay Pages: 6

Brand: Elkay Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands