ATH-Heinl ATH 4.35 User Manual Download Page 2

Page: 2 / 63

Content

........................................................................................................................................................................... 3

General Information

......................................................................................................................................................... 3

Description of the 4 post lift

............................................................................................................................................ 4

Main components

............................................................................................................................................................. 5

Safety devices

.................................................................................................................................................................. 5

Operation

........................................................................................................................................................................... 6

Technical data

.................................................................................................................................................................. 7

Scope of delivery

............................................................................................................................................................ 10

INSTALLATION

.................................................................................................................................................................. 11

Floor foundation

............................................................................................................................................................. 11

Place of Installation

........................................................................................................................................................ 13

Installation of the lift

....................................................................................................................................................... 14

OPERATION

....................................................................................................................................................................... 21

Warning symbols

............................................................................................................................................................ 21

Operating instructions

................................................................................................................................................... 22

Utilization

......................................................................................................................................................................... 23

MAINTENANCE

................................................................................................................................................................. 24

Care instructions

............................................................................................................................................................ 24

Troubleshooting

.............................................................................................................................................................. 24

Maintenance plan

........................................................................................................................................................... 26

Lubrication plan

.............................................................................................................................................................. 27

Maintenance- and service instructions

....................................................................................................................... 27

KONFORMITÄTSERKLÄRUNG

...................................................................................................................................... 29

Spare part list

...................................................................................................................................................................... 30

Appendix

.............................................................................................................................................................................. 42

Electric diagram 400 V

..................................................................................................................................................... 42

Hydraulic diagram

.......................................................................................................................................................... 44

Pneumatic diagram

........................................................................................................................................................ 45

WARRANTY NOTE

........................................................................................................................................................... 46

Checking book

.................................................................................................................................................................... 48

NOTES

................................................................................................................................................................................. 61

Summary of Contents for ATH 4.35




















































Search results

Summary of Contents for ATH 4.35

Reviews:

Brands by name

Popular brands

ATH-Heinl ATH 4.35, User Manual

Search results

Summary of Contents for ATH 4.35

Reviews:

Brands by name

Popular brands