background image

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Sale Date

 

Seller Company;

 

 
 

 
 
 

The Machines which are produced By ATEK MAKINA are under warranty against defects 
of the material and production for one(1) Year from date of it is sold. 

Our  Company  ATEK  MAKINA  is  not  responsible  for  the  damages  or  defects  due  to 
damages occured by faulty used and out of purpose of use. 

If the Defects and damages are occured during the warranty, After making analysis by 
technical staff, If the Material and production fault is found, the damaged parts will be 
replaced with new one  

Warranty covers all parts of the machine during the warranty. 

ATTENTION: you have to put thermic switch which is suitable to motor ampere on your 
electric wiring to make Electric motor under warranty otherwise in case of any defect 
the Electric Motor will not be under warranty. 

Do  Make  Maintanence  of  the  machine  periodicly,  monthly,  yearly,  The  defects, 
damages which are caused by not making maintanence will not be undur warranty. 

Atek Machina; 

Without notice to the customer reserves the right to make changes in equipment. 

 

 

Summary of Contents for JUMBO DOUBLE



















Reviews: