background image

This product is intended only to mount a television of the indicated size and weight. Using this 

product to mount televisions heavier than the maximum weight capacity can damage equipment

and cause personal injury.

Schoenfeld International Inc. and ATEC are not responsible for personal injury or product 

damage due to mishandling, incorrect mounting, incorrect assembly, or incorrect use of this 

product.

How and where you use your television wall mount is extremely important for Child Safety

As you set up and use your new product, keep all of these safety tips in mind.

• One size of TV wall mount does not fit all TVs. Use only a TV wall mount rated for the weight 

of your TV and the size of your screen. Your TV wall mount assembly instructions contains 

specific information on the maximum weight and screen size combination that your wall 

mount can safely support. Do not exceed the maximum weight of screen size for any TV wall 

mount.

• Carefully read all of enclosed instructions for proper use of this product. If you have any 

doubts about safe and secure assembly, please contact a professional. 

• Don’t let children climb on or play with mounts or TVs.

• Remember that children can become excited while watching a program, especially on a 

“larger than life” TV. Make sure to place or install the TV wall mount where it cannot be 

pushed, pulled on, or knocked down.

• Make sure that you route all cords and cables so that they cannot be pulled or grabbed by 

curious children.

Always wear safety goggles to when drilling or installing hardware.

Tools

For your convenience, we have included an allen wrench with this mount. For the best assembly 

experience and mounting safety, we always recommend using full-size tools for each assembly 

step.

Below is a recommended tool list you will need for proper and safe installation. See applicable 

warnings in this manual about certain types of mounting surface materials and the special hardware

and tools that should be used.

• Drill with a specific size drill bit to pre-drill holes in the wall

• Stud finder

• Tape measure

• Pencil

• Screw drivers

• Socket wrenches

• Small hammer

• Safety goggles

Summary of Contents for A590TM

















Reviews: