AT&T MLC-5 Supplementary Manual Download Page 2

TELEPHONE

MLC-5 Cordless Telephone Handset

Imprinted Buttons

Button
Labeling

Card

Channel

Button

Line
Buttons

Low
Battery
Light

Message
Light

Card used to note
feature or line assigned
to each line button.

Button used to change
channels for improved
reception.

Five buttons with red
lights, used to make/
receive calls. Any
unlabeled buttons can
be programmed with
features.

Light blinks when
batteries have less than

15 minutes of use

remaining (tone also
generated).

Light illuminates

when you have a voice-

mail message, fax, or a
message from the

Imprinted buttons, including dedicated

feature buttons, cannot be changed.

Hold

Status

Transfer

Channel

system operator.

On/Off

MLC-5 Cordless Telephone Base Unit

Antenna

Battery
Contacts

Channel
Indicator

Directory
Card

Message
Light

Retractable antenna;
extend fully for clear

reception.

Mode

Metal contacts that

Lights

recharge the handset.
Clean contacts
periodically with a soft
pencil eraser.

Electronic display of

the channel currently

used or programmed.
A "P" displays when
the telephone is being

programmed.

Erasable card used to
record the telephone
number assigned to the
cordless telephone and
to list feature codes.

Light illuminates when

you have a voice-mail

message, fax, or
message from the
system operator.

Ringing
Volume
Control

Press to put a call on hold.
Red light flashes while call
is on hold. During hold,
phone beeps every 60
seconds. More than one
call can be on hold at a
time.

Press to show on the
status of the handset line
button lights, except for
On/Off, Low Battery,  and
Message.  Light turns
off after 20 seconds.

Press to send a call to
another phone.

Press to change the
channel to improve
reception.

Press to activate the
handset to make or
answer a call.

Charge - a light that

illuminates when the
handset is in the the base
unit and the batteries are
c h a r g i n g .

Talk - a light that

illuminates when the
handset is removed from

the base unit and, is turned
on using On/Off  button.

Program - a light that
illuminates when the T/P
switch is set to P for
programming.

Sliding control used to
adjust the volume of the

base unit’s ring.

Switch used to test and
program the telephone.

T/P

Switch

Summary of Contents for MLC-5









Reviews: