background image

Fire Prevention

Rubber track loaders have components

that operate at high temperatures. The
main heat sources are the engine and the
exhaust system. The electrical system
can also be a source of heat or sparks if
damaged or improperly maintained. 

In some work environments, flamma-

ble items such as leaves, straw, and
brush cutting debris may come in con-
tact with these items. It is very impor-

tant that flammable items be removed
often from close proximity to these high
temperature items. If debris is allowed
to accumulate, a fire may result posing a
risk to the operator and the machine. A
fire can cause machine damage, severe
injury, or even death.

Overheat Prevention

The radiator/oil cooler must be inspected
for signs of clogging and cleaned daily
or more often as needed to prevent the
engine and hydraulic system from over-
heating

Listed are a set of precautionary tasks

that should be performed daily or more
often if necessary. Repair or replace
worn or damaged components as needed
to ensure safe machine operation.

Precautionary Tasks

• With the engine off and cool, clean

dirt/debris from the radiator/oil cooler,
engine compartment, exhaust system,
attachments and other areas where
there may be hot or rotating parts.
Remove the belly pans and pressure
wash these items and all surrounding
areas until clean.

• Check battery, fuse box, electrical

wiring and connections for damage or
looseness.

• Check fuel and hydraulic lines/hoses

for leaks or damage. Never use bare
hands to check for leaks. Pressurized
fluid can penetrate skin and cause
injury or even death.

6

Safety Warnings

1. Remove any attachment
from the machine.
2. Have an second person
remove the lift arm brace.
3. Raise the lift arms.
4. Have the second person
place the lift arm brace onto the
top side of the cylinder ram.

5. Install the retaining pins
using the holes labeled with the
arrows.
6. Slowly lower the lift arms
until they contact the brace.
7. Reverse these steps to

disengage the lift arm brace

WARNING

If  instructions to safely install
lift arm brace are not followed
injury or death could result.

NEVER GO BENEATH UNSECURED LIFT ARMS

0201-752

!WARNING!

• Never use ether or any other aerosol type starting aid to start the engine.

• Always stop the engine and allow the machine to cool before adding fuel. 

• Never smoke or allow open flame near the machine while refueling.

Summary of Contents for R Series





























Reviews: