Asus TS150-E2, User Manual

Page: 61 / 134

4 - 1 3 4 - 1 3 4 - 1 3 4 - 1 3 4 - 1 3 A S U S T S 1 5 0 - E 2 A S U S T S 1 5 0 - E 2 A S U S T S 1 5 0 - E 2 A S U S T S 1 5 0 - E 2 A S U S T S 1 5 0 - E 2
3 . 3 .
3 . 3 . 3 .
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 ,
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 ,
S A T A 4 )
S A T A 4 ) S A T A 4 ) S A T A 4 ) S A T A 4 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0 or
RAID 1 configuration with the onboard Intel
® ICH6R RAID controller.
These connectors are set to S t a n d a r d I D E S t a n d a r d I D E
S t a n d a r d I D E S t a n d a r d I D E
S t a n d a r d I D E mode by default. In
S S
S S
S t a n d a r d I D E t a n d a r d I D E
t a n d a r d I D E t a n d a r d I D E
t a n d a r d I D E mode, you can connect Serial ATA boot/data hard disk
drives to these connectors. If you intend to create a Serial ATA RAID set
using these connectors, set the C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s item in the BIOS
to [RAID]. See section “5.3.5 IDE Configuration” for details.
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
• You must install Windows ® 2000 Service Pack 4, Windows ® 2000
Advanced Server, or Windows ® Server 2003 before using Serial ATA
hard disk drives. The Serial ATA RAID feature (RAID 0and RAID 1) is
available only if you are using Windows
®
2000/2003 Server.
• Use only two Serial ATA RAID connectors for each RAID 0 and
RAID 1 set.
• When using the connectors in S S
S S
S tandard IDE t a n d a r d I D E
t a n d a r d I D E t a n d a r d I D E
t a n d a r d I D E mode, connect the
primary (boot) hard disk drive to the SATA1 or SATA2 connector.
Refer to the table below for the recommended SATA hard disk drive
connections.
Serial ATA hard disk drive connection Serial ATA hard disk drive connection
Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection
C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r S e t t i n g S e t t i n g S e t t i n g S e t t i n g S e t t i n g U s e U s e U s e U s e U s e
S A T A 1 , S A T A 2 S A T A 1 , S A T A 2 S A T A 1 , S A T A 2 S A T A 1 , S A T A 2 S A T A 1 , S A T A 2 M a s t e r M a s t e r M a s t e r M a s t e r M a s t e r B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k
S A T A 3 , S A T A 4 S A T A 3 , S A T A 4 S A T A 3 , S A T A 4 S A T A 3 , S A T A 4 S A T A 3 , S A T A 4 S l a v e S l a v e S l a v e S l a v e S l a v e D a t a d i s k D a t a d i s k D a t a d i s k D a t a d i s k D a t a d i s k
P5CR-VM
P5CR-VM SATA connectors
SATA2
SATA1
SATA4
SATA3
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXP4
RSATA_RXN4
GND
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND