manualshive.com logo in svg

Asus P2B98-XV, User Manual, Page: 58 / 88

Share
Download
Asus P2B98-XV User Manual Download Page 58

58

ASUS P2B98-XV User’s Manual

A. Video Driver

First Time Installation

When starting Windows 95 (OSR2.0) or Windows NT 4.0, the operating system will
detect that you have a new PCI Multimedia Device, then an Update Device Driver
Wizard will appear.

1. Click Next.

3. Click the Browse button to locate the

“\DRIVERS\ATI435\WIN95” (or NT40) direc-
tory on the ASUS Support CD.

4. Click OK and “RAGE PRO TURBO 2X (En-

glish) (DirectX)” will appear.  Click Finish.
Click No when asked if you want to keep files
during version conflicts.

8. You will be prompted to locate disk #2 of the

drivers.  Click Ok and then click  Browse and
locate the “\DRIVERS\ATI435\WIN95” (or
NT40) directory on the ASUS Support CD again.

7. You will be prompted to locate disk #1 of the

drivers.  Click OK and then click Browse and
locate the “\DRIVERS\ATI435\WIN95” (or
NT40) directory on the ASUS Support CD.

2. Click Other Locations to direct the wizard to

the audio driver files.

A. V

ideo Driver

First T

ime 

Install

Summary of Contents for P2B98-XV

























































































Reviews:

No comments