8
Two types of confirmations are displayed on the remote:
Command confirmation: These confirmations are command acknowledgements. The icon corresponding to the command is displayed to confirm the reception
of the command.
Status confirmations: These confirmations are displayed when the status of a monitored zone changes: door opening, alarm state, etc.
Command confirmations are returned immediately following a command transmission, whereas the status confirmations may be returned up to 12 seconds after
the event happened.
Out of range: In the event that the environment prevents confirmations from being received by the remote control, the “X” icon appears.
Note: You can refresh the LCD screen display by pressing on any button or press the status button.
CONFIRMATIONS EMITTED BY VEHICLE
Confirmations emitted by the vehicle are sent as soon as the command is received by the start module. In most cases, your remote starter will confirm that the
command has been received, either by sounding the horn, the siren, or by flashing the parking lights.
The confirmations emitted by the parking lights are mandatory while those emitted by the horn and the siren are optional (programmable) and can require
connections and additional equipment at time of installation. Many of these confirmations depend on the system’s status when the command is emitted. Refer to
paragraphs relating to each command for more details on confirmations.
LOCK/UNLOCK COMMANDS AND ALARM SYSTEM ARMING/DISARMING
If your vehicle is equipped with electric door locks, several functions can be operated by remote control.
These features are optional and may require purchasing additional equipment. Consult your dealer for advice.
Arming and disarming the security system also controls the Lock/Unlock functions. The arming/disarming functions only apply to models equipped with a security
system.
The following systems can be controlled:
•
Door locks
•
Trunk or hatchback release
•
Interior lights
LOCK / ARM
Press the
button: the doors are locked and the alarm system is armed. The parking lights flash once and the siren chirps once (if programmed during
installation) to confirm that the command has been received and that none of the protected zones are in violation.
The parking light confirmation is sent as many times as the command is repeated, so you are sure that the system has received the command. The audible
confirmation is also repeated (siren or horn, depending on programming) if option "Confirmation on 2nd lock" is activated (during installation).
If a zone is in violation during arming, the confirmation warning you is different (3 flashes or chirps). See table of alarm codes to know which zone is in violation.
UNLOCK / DISARM
Press the
button. The doors are unlocked and the alarm is disarmed. The parking lights flash and the siren chirps twice to confirm that the command has
been received and that no alarm condition was generated during your absence.
If there was a violation, the confirmation would be different (4 flashes or chirps). See table of alarm codes to know which zone generated an alarm condition.
The “Unlock“ function can be programmed and connected in such a way that the first Unlock command only unlocks the driver's door, while a following Unlock
command unlocks the other doors (optional connection during installation).
The dome light will turn on for 30 seconds every time the Unlock command is sent out (not applicable in semi-passive mode)(optional connection during
installation).
This 30-second duration is cancelled when the Lock command is sent out, when the brakes are applied or the key is inserted in the ignition and turned to the
RUN position.
TRUNK RELEASE
(This feature must be enabled during the installation).
Press the
button and hold it for 4 seconds. The trunk is released and the parking lights flash three times to confirm that the command has been executed.
The remote shows the trunk opening.
The trunk cannot be released if the ignition key is in the RUN position.
Furthermore, if the alarm is armed and the system is not equipped with an additional sensor capable of detecting trunk release (optional equipment not included),
the opening of the trunk with a remote control will not be possible.
In this case, the parking lights flash once and the remote control vibrates once to confirm that the command has been received, but the trunk could not be
released.
If you are not sure you have received confirmation, repeat the command. The system will repeat the confirmation as often as you wish.
If your vehicle is equipped with a factory installed security system and that this system is neutralized by the trunk release command, remember to rearm it after
the trunk is closed ("Lock" command).
