manualshive.com logo in svg

ASTRO-PHYSICS Mach1GTO, Manual, Page: 31 / 31

Share
Download
ASTRO-PHYSICS Mach1GTO Manual Download Page 31

p

t

p

p

t

t

p

Astro-Physics Mounting Plate Fastener Chart

15" Flat 

Plate 

(FP1500)

18" Flat 

Plate 

(FP1800)

8" Dovetail 

Plate 

(DOVE08)

15" Dovetail 

Plate 

(DOVE15)

Dovetail Plate 

for Losmandy D 

Series Plate 

(DOVELM2)

Dovetail Plate 

for Losmandy D 

Series Plate 

(DOVELM16/S)

15" Ribbed 

Plate 

(900RP)

15" Ribbed 

Plate 

(1200RP15)

24" Ribbed 

Plate 

(1200RP)

400 

Mounts

(4) ¼-

20x5/8" 

Socket Head

Cap Screw

(4) ¼-20x1/2" 

Socket Head 

Cap Screw

(4) ¼-20x1/2" 

Flat Socket Ca

Screw **

(4) ¼-20x5/8" 

Socket Head Cap 

Screw

Not Recommended

(4) ¼-20x7/8" 

Socket Head Cap 

Screw

600E 

Mounts

(4) M6-1.0x 

20mm 

Socket Head

Cap Screw

(4) M6-1.0x 

16mm Flat 

Socket Cap 

Screw

(4) M6-1.0x 

16mm Flat 

Socket Cap 

Screw *

(4) M6-1.0x 20mm 

Socket Head Cap 

Screw

Not Recommended

(4) M6-1.0x 25mm 

Socket Head Cap 

Screw

900 

Mounts

(4) ¼-

20x5/8" 

Socket Head

Cap Screw 

(6) ¼-20x1" 

Flat Socket 
Cap Screw

(4) ¼-20x5/8" 

Socket Head 

Cap Screw

(4) ¼-20x5/8" 

Flat Socket Ca

Screw

(1) ¼-20x5/8" Flat 

Socket Cap Screw

(2) ¼-20x1" Socke

Head Cap Screw

(6) ¼-20x1" 

Flat Socket 
Cap Screw

and         

(6) ¼-20x5/8" 

Flat Socket 
Cap Screw 

Use Q4047 

Adapter

and             

(1) ¼-20x3/4" 

Socket Head Cap 

Screw

or              

(4) ¼-20x1" Socke

Head Cap Screw

or               

(4) ¼-20x3/4" 

Socket Head Cap 

Screw

1200 

Mounts

(4) ¼-20x¾" 

Socket Head

Cap Screw

(6) ¼-20x1" 

Flat Socket 
Cap Screw

(4) ¼-20x5/8" 

Flat Socket Ca

Screw

(2) ¼-20x5/8" Flat 

Socket Cap Screw

(2) ¼-20x1" Socket

Head Cap Screw

(6) ¼-20x3/4" 

Socket Head 

Cap Screw

(6) ¼-20x1" 

Socket Head 

Cap Screw

and/or           

(4) ¼-20x¾" Socke

Head Cap Screw

and/or           

(4) ¼-20x1" Socket

Head Cap Screw

Mach1 

GTO 

Mounts

(4) ¼-

20x5/8" 

Socket Head

Cap Screw

(4) ¼-

20x1¼" Flat 

Socket Cap 

Screw

(4) ¼-20x5/8" 

Socket Head 

Cap Screw

(4) ¼-20x1/2" 

Flat Socket Ca

Screw **

(4) ¼-20x5/8" 

Socket Head Cap 

Screw

(4) ¼-20x7/8" 

Socket Head Cap 

Screw

(4) ¼-20x1¼" 

Flat Socket 
Cap Screw

and          

(4) ¼-20x1" 

Flat Socket 

Cap Screw. 
Use Q4047 

Adapter

As Accessory

(4) 10-32x¾" 

Socket Head 

Cap Screw

(4) 10-32x¾" 

Socket Head 

Cap Screw

* 4mm Hex Key

** 5/32" Hex Key

Plate

3/30/2007

Summary of Contents for Mach1GTO
































Reviews:

No comments