background image

Operation 

900697-00E  10/2018

Innovative Hearth Products
Altair™ Series Direct-Vent Gas Fireplaces

57

 WARNING 

• Do not attempt to substitute the materials used on these doors, or replace cracked or broken glass. 
• Handle this glass with extreme care! Glass is susceptible to damage—Do not scratch or handle roughly 

while reinstalling the glass door frame.

• The glass door of this appliance must only be replaced as a complete unit as provided by the 

manufacturer. Do not attempt to replace broken, cracked or chipped glass separately. 

• Do not attempt to touch the front enclosure glass with your hands while the fireplace is in use.

 WARNING 

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and 

shall be installed.

 AVERTISSEMENT 

Une barrière conçue pour réduire le risque de brûlure par le hublot chaude est fournie avec l’appareil et doit 

être installé.

 WARNING 

Do not operate appliance with the glass front removed, cracked, or broken.

 AVERTISSEMENT 

Ne pas utiliser l’appareil si le panneau frontal en verre n’est pas en place, est craqué, ou brisé.

 WARNING 

Any safety screen, guard or barrier removed for servicing an appliance must be replaced prior to operating 

the appliance.

 AVERTISSEMENT 

Tout écran ou protecteur retiré pour permettre l’entretien de l’appareil doit être remis en place avant de 

mettre l’appareil en marche.

Only doors certified with the fireplace shall be used.

Seules des portes certifiées pour cet appareil doivent être utilisées.

Installing and removing the glass door

 WARNING

Do NOT abuse the glass door by striking it or slamming it shut.

 WARNING

The door should easily close without needing to be pressed down. If it has to be pressed down to close, the 

gasket in the top of the door should be dressed so it lays on the glass.

f i r e - p a r t s . c o m

Summary of Contents for Altair 40DEN-B











































































Reviews: