background image

INST 291 RC9 Series Controller V12_17 
 

14 

Squeeze tube needs replacement. 

Water returns to the chemical drum  

Check last 3 points above. Replace non-return Valve if 

fitted. If not please fit. 

Numbers not appearing on display 
panel, no lights or power 

Turn off for 15 minutes, and then restart. If still no 

response, contact AstralPool Service. 

 

IMPORTANT: ELECTRICAL SPIKES/SURGES OR SIMILAR SITUATIONS CAN EFFECT THE ELECTRONICS 
& SENSORS AND CAUSE THE MACHINE TO MALFUNCTION. IT IS NECESSARY TO CHECK THE WATER 
CHEMISTRY, ESPECIALLY PH AND CHLORINE LEVELS REGULARLY WITH A GOOD QUALITY TEST KIT 
AND LOOK OUT FOR ANY MALFUNCTIONS. 
IF THE PH AND/OR ORP READING ON THE RC MACHINE ARE OUT OF NORMAL RANGE PLEASE TURN 
THE MACHINE OFF AND CALL A POOL TECHNICIAN OR ASTRALPOOL 
 
ALWAYS USE GENUINE ROLA CHEM PARTS.  
AstralPool reserves to change product specifications without notice. 
Please check AstralPool web site at 

www.astralpool.com.au

 for updates before installing or servicing Rola Chem units. 

RC9 – MAINTENANCE SCHEDULE 

 

You new product incorporates moving parts and withstands high velocity water with chemicals in it.   Some of these 
parts will wear in the normal course of use and require regular checks and maintenance.    Performing these checks and 
maintenance will identify parts that have worn and require repair/replacement before further serious damage is 
sustained.   A small amount of regular care and attention to your pool equipment will help ensure long life and trouble 
free performance.
  
 
 

Timing 

Maintenance Check 

Service action (if required) 

Fortnightly 

Check acid / chlorine drums 

Fill drums, use a 2:1 mixture for acid 

Three Monthly 

Check supply tubes for blockages 
 
Check pH and ORP probes 
 
 
 
Check non return valves in drums 

Cut ends off supply tubes if build up of scale 
and reconnect 
Clean with abrasive crème cleanser (do not 
use acids), reassembly and allow at least 1 
hour for sensing to return to normal 
Replace if required 

Six Monthly 

Check output settings and adjust 
 
Check squeeze tubes 
 
Spray around equipment for insects 
 
Recalibrate sensors 

Adjust timer / output settings based on 
season, weather and pool usage 
Apply grease if required, replace if leaking 
Spray on surrounding walls, do not spray 
directly into appliance 
Follow instructions in this manual 

Annually 

Check all connections, o’rings and tubing 

Call Service technician to perform annual 
checks and routine maintenance 

 

Important note: Regular maintenance is important to ensure long life and trouble free performance of your pool 
equipment.   If unable to perform the maintenance yourself, contact your local AstralPool office who will arrange a trained 
service technician to perform the maintenance for you. 

 
 
 
 
 
 
 
 
 
 

Record your Equipment details here for quick reference: 
 
 

Model No.: 

____________________________ 

 
 

Serial No.: 

____________________________ 

Summary of Contents for RC 9 ORP and pH Combined

















Reviews: