background image

 
Note: please refer to the AT200 Installation Guide for installation and calibration guidance 
relating to the use of IGNM mode 3. 

 

STOP Report Delay (STPD) 

When IGNM is set to zero (see above), the AT200 will determine journey START and STOP 
events based on movement data from GPS, accelerometer and tremble sensor.  A STOP 
event will occur after the vehicle has remained stationary for a pre-determined time.  The 
length of stationary time necessary to trigger a STOP report is dictated by the STPD 
parameter. 
 
When using IGNM 3 to detect journey status from external voltage, a STOP event will 
occur after the vehicle voltage has dropped for a pre-determined time, to prevent false 
journey STOP events during engine automatic start/stop.  This delay time is dictated by 
the STPD parameter.   

 

 
Driver ID Settings: 

 

Driver ID Configuration (DRIC) 

Command to configure driver ID source, authorisation, reporting and timeouts. 
 
$DRIC,<driver_id_source>,<reminder>,<confirm>,<report_all>,<immobilise>, 

<validity_timeout_secs>,<auth_timeout_secs>,<imob_output_state>, 
<server_authorisation> 

 
where: 
 
<driver_id_source>   

0=none, 1=iButton, 2=Mifare card, 3=Bluetooth 

<reminder> 

Set to 1 to enable an indicator when ignition is turned ON 
until iButton is presented 

<confirm> 

Set to 1 to enable an indicator (short pulse) whenever an 
iButton is read 

<report_all> 

Set to 1 to enable to enable an event/report each time an 
iButton is presented 

<immobilise> 

Set to 1 to enable the output switch is used to disable the 
vehicle until an iButton is presented 

<validity_timeout_secs> 

Driver ID validity timeout.  Driver ID data will be attached to 
all journey START and STOP reports until validity expires.  
Default is 7200. 

<auth_timeout_secs> 

Driver ID authentication timeout.  Driver ID must be 
presented before the vehicle engine is started.  If no Driver 
ID was seen for 

auth_timeout_secs

 the AT200 output switch 

will be activated if reminder or immobilise option is set.  
Default is 30. 

<imob_output_state> 

The state of the digital output when immobilisation is active. 
0 = output OFF for immobilisation. 1 = output ON for 
immobilisation. 
Default is 0. 

<server_authorisation> 

This controls whether a driver ID must be authorised by the 
server using the commands described in the section 
Authorised Driver Implementation in Utility and Engineering 
Commands. 
0 = server authorisation not required. 1 = server 
authorisation required. 

 

Summary of Contents for AT200





























Reviews: