background image

Page: 3

Caution:

 The unit is fitted with a

n obstacle sensing switch

, if the unit encounters an obstruction 

under the front portion of the basin whilst travelling downwards it will automatically stop. Pressing 

the ‘Up’ 

button will allow the obstruction to be removed. Care should be taken to ensure that 

whilst the basin assembly is moving downwards there are no obstructions left directly 

beneath the basin or rise & fall unit as the 

obstacle sensing switch

 is designed to 

stop the unit only when the front of the basin is lifted. 

If both the ‘Up’ and 

Down’ buttons are pressed at the same time the unit will not 

move.

Cleaning

The basin and vanity top may be cleaned using most mild cleaning agents. Chemical agents must not 

be used, i.e. drain cleaners, acetone, oven cleaners or acids. The rise and fall unit and handset 

should be cleaned using a warm soapy solution and rinsed with a damp cloth. Attention should 

always be paid to instruction labels on the outside of cleaning agent containers.

 Test the cleaner on 

a discrete area (e.g. underneath the unit).

Troubleshooting

In the unlikely event that problems occur with t

he unit, carry out the following easy checks to

 

determine whether or not an engineer is required

:

 

Fault: 

 

The rise and fall unit does not travel up or down

.

Cause: 

 

The mains power supply 

may have

 been disconnected

.

 

Remedy: 

 

Examine the mains fuses/circuit breakers and reset as necessary and ensure that mains voltage is 

fully reconnected

.  

If the 

unit still 

fails to 

oper

ate an electrician needs to ensure that mains 

electrical supply is available at the fused spur (a fuse may have blown elsewhere in the circuit)

.

Fault:

Cause:  

The rise and fall unit travels upwards but not downwards

There 

may be 

an obstruction underneath the basin

.

Remedy:

 

Depress the ‘Up’ button on the handset to gain clearance from the obstruction and then remove the 

obstruction. The rise & fall unit 

should

 then resume normal function

.

If the problem persists after carrying out these remedies, please

 

contact Astor-Bannerman 

(contact 

details can be found

 on the back page

 of this user guide)

.

Our policy is one of continuous improvement and we therefore reserve the right to make 

technical alterations without notice. 

 

The content of this publication may not be copied 

either whole or in part without the consent of Astor–Bannerman. 

 Version 

4

 : 

2

5

-0

9

-01

9

Summary of Contents for ABW-CP













Reviews: