background image

Customer is required to provide adequate access the Product for any repair or 

inspection.  Aston Global shall not be liable for expenses or damage which may include 

but are limited to water damage, removal of any and all common building product such 

as tile, flooring, wood, sheet rock, plumbing fixtures,  concrete board, vanities, bathtubs 

and toilets or any other custom items. 

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE 

OTHER RIGHTS WHICH VARY FROM STATE TO STATE. ASTON GLOBAL'S 

FAILURE TO ENFORCE ANY TERMS OR CONDITIONS STATED HEREIN SHALL 

NOT BE CONSTRUED TO BE A WAIVER OF SUCH PROVISION. 

For prompt service, notify the original installer who, in turn, will notify the Aston Global 

distributor who supplied the Product.  If this does not result in prompt service, contact 

Aston Global,  Inc. at the address below with details in support of the warranty claim.  For 

any questions about coverage of this Warranty, contact Aston Global at the address 

below. 

Aston Global offers free phone support for the life of the Product to the original 

Owner. 

The Warranty applies only to Products manufactured on or after January 1, 2012. 

This Warranty may not be combined with any other warranty offered by Aston 

Global. 

21 

Summary of Contents for Orbitus SEN980
























Reviews: