manualshive.com logo in svg

assfalg-metal SAFEBAT SB200, Operating Manual, Page: 14 / 24

Share
Download
assfalg-metal SAFEBAT SB200 Operating Manual Download Page 14

[email protected]

 

www.assfalg-metal.com 

 
 

[13] 

 

Assfalg GmbH Buchstraße 149 73525 Schwäbisch Gmünd / Germany  +49 (0)7171 92505-0 Fax +49 (0)7171 92505-50 

 

 

8.5

 

Automatic mode 

In automatic mode, the SAFEBAT automatically magnetizes / demagnetizes each time it is hoisted and 
then lowered. 

Before using automatic mode make sure the ADPREM magnet is securely fastened. 
CAUTION: Only use automatic mode in a restricted area free from personnel. 

To activate the automatic mode, press the MAG and DEMAG buttons at the same time. 
The automatic mode indication LED lights up to show that the automatic mode is activated. 

 

 

 

 

To deactivate the automatic mode, press the MAG and DEMAG buttons at the same time. 
The automatic mode indication LED goes off to show that the automatic mode is deactivated.

 

In automatic mode, the SAFEBAT turns itself automatically OFF after 15 minutes of inactivity. 

 

8.6

 

Holding force levels 

The SAFEBAT offers three holding force levels. By default, the level is always pre-set at the maximum 
holding force level 3. 

The currently selected holding force level is indicated while pressing the associated button. 

 
 
 
 
 
 
 
 
 
 
 
 
 

The three green LEDs above the MAG Button show the currently selected holding force level. 

The holding force level can be changed only when the SAFEBAT is demagnetized.  Reduce the holding 
force in two cases: the sheet thickness is below 12mm or the lifting magnet hoists more than a single 
sheet. Safe lifting is only possible with one sheet hoisted at a time. 

Summary of Contents for SAFEBAT SB200

























Reviews:

No comments