manualshive.com logo in svg

Assa Abloy SARGENT 2900 FIREGUARD, Installation Instructions Manual, Page: 1 / 8

Share
Download
Assa Abloy SARGENT 2900 FIREGUARD Installation Instructions Manual Download Page 1

NOTE:

Devices are handed and must be

the same hand as door.

RH - Right Hand Door

LHR - Left hand Reverse

LH - Left Hand Door

RHR - Right Hand Reverse 

MODEL 2960

RH - Right Hand Door

LHR - Left Hand Reverse

LH - Left Hand Door

RHR - Right Hand Reverse

NOTE: Devices are handed and must be the same hand as door.

INSTALLER: LEAVE INSTRUCTIONS FOR BUILDING OWNER

Installation Instructions

1-800-810-WIRE (9473) • www.sargentlock.com

A7396E  09/21

Copyright © 2005, 2008, 2011, 2021, SARGENT Manufacturing Company. All rights reserved. Reproduction in 

whole or in part without the express written permission of SARGENT Manufacturing Company is prohibited.

 WARNING

This product can expose you to lead 
which is known to the state of California 
to cause cancer and birth defects or other 
reproductive harm. For more information 
go to www.P65warnings.ca.gov.

2900 FIREGUARD

®

 

Electromechanical Closer-Holder

 

2980 Multipoint Hold Open with Swing Free Arm

Pull (Hinge) Side

Summary of Contents for SARGENT 2900 FIREGUARD









Reviews:

No comments