background image

 
Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. 
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 

80-9372-0100-015 (02-14)

ASSA ABLOY

RI X SON

®

1

Requirements:

Units are handed. Hand of unit and hand of door must be the same.

All dimensions shown in inches (mm).

Door must be hung on ball bearing butt hinges or 3/4" (19) offset pivots.

Door thickness must be 1-3/4" (44) to 2-1/4" (64).

Door must swing freely through the entire opening and closing cycle before beginning the installation procedure.

Frame face must be a minimum of 2" (51).

Ceiling clearance must be a minimum of 3 -1/2" (89) for push side application or 4" (102) for pull side application. See pages 
2 and 7 for templates.

Power input to unit must be of the same voltage as that stated on the unit.

Unit to be mounted on interior of building in dry environment, maximum humidity of 95%.

See NFPA70 for wiring requirements and NFPA72 for alarm system requirements.

Pull Side Applications with Slide Track
(4 Pull, 6 Pull)

(see page 7 for template)

Push Side Applications with Double Lever Arms
(4 Push, 6 Push)

(see page 2 for template)

Item No. Description

1           Track (Pull Side)

2           Cover
3           Track Arm (Pull Side)
4           Double Lever Arm (Push Side)

• Allen wrench set (inch)
• Flat blade screwdriver (potentiometer & 
terminal size)
• Screwdriver (Phillips size 2)

      • Tape ruler

• Power drill 
• Center punch
• Wire stripper

Tools required:

Use screw pack and hardware provided to mount operator. 

3

1

2

4

Table of Contents:

Push  Side Template....................2
Push  Side  Installation..............2-4
Closer  Adjustments.....................5
Hold Open Position Adj...............6
Pull  Side  Template......................7
Pull Side Installation.................7-9
Closer  Adjustments...................10
Hold Open Position Adj.............11
Non-Detectored  Electrical.........12
Detectored  Electrical.................13
RF Unit Electrical.................14-15
Troubleshooting.........................15
General  Information..................16

ASSA ABLOY

RI X SON

®

Smok-Chek® VI 

Installation and Instruction Manual

ASSA ABLO

Y

RIX SO

N

®

ASSA ABL

OY

RIX S

ON

®

Summary of Contents for Rixson Smok-Chek VI

















Reviews: