Assa Abloy PDU8500 Series Manual Download Page 5

Page: 5 / 16

Copyright © 2020-2021, ASSA ABLOY Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Inc. is prohibited.

• Remove

"-20 Set Screws on Interior Pivot Bracket Post.

• Unscrew and remove Conehead Union (

"-18).

• Remove Metal Washer, Alignment Bushing and Spacer.

2.1.5 Remove Vertical Door Mount

Shipping Board

Interior Pivot Bracket Post

Panic Device

Set Screws

Shipping Board

Metal Washer

Alignment

Bushing and

Spacer

Mating Pull

Conehead

Union

• Unscrew and remove the Conehead Union (

"-18).

• Remove the Deco End Cap.
• Remove the Metal Washer, Alignment Bushing and

Spacer.

2.1.3 Remove Horizontal Door Mount

• Unscrew and remove the Conehead Union (

"-18).

• Remove the Metal Washer, and Alignment Bushing and

Spacer.

Shipping Board

Deco End Cap

Metal Washer

Conehead

Union

Alignment

Bushing and

Spacer

2.1.4 Remove Horizontal Door Mount (Deco End Cap Option)

Summary of Contents for PDU8500 Series

















Search results

Summary of Contents for PDU8500 Series

Reviews:

Related manuals for PDU8500 Series

Brands by name

Popular brands

Assa Abloy PDU8500 Series, Manual

Search results

Summary of Contents for PDU8500 Series

Reviews:

Related manuals for PDU8500 Series

Brands by name

Popular brands