Assa Abloy HES Aperio K100 Installation & Operating Instructions Manual Download Page 9

Page: 9 / 12

Strike Plate

Installation

ALIGN strike plate template

to centerline and edge of

cabinet. Drill mounting holes.

SECURE strike plate to inside

cabinet wall using

2x Screw d

BUT DO NOT FULLY TIGHTEN.

Adjust strike plate so the

edge is flush with the cabinet

wall edge then tighten.

After the strike plate is in

the desired position, fasten

Screw d

into strike plate as

shown in Diagram 15.

Double Door

Strike Plate

Installation

ALIGN double door bracket

with mounting holes from

the strike plate template.

Secure strike plate to the double

door bracket using

Screw d

as shown in Diagram 16.

Diagram13:

Strike Plate Template Use

Diagram16:

Double Door Strike Plate Installation

Diagram14:

Strike Plate Installation

Diagram15:

Step 3

of 12

Summary of Contents for HES Aperio K100













Search results

Summary of Contents for HES Aperio K100

Reviews:

Related manuals for HES Aperio K100

Brands by name

Popular brands

Assa Abloy HES Aperio K100, Installation & Operating Instructions Manual

Search results

Summary of Contents for HES Aperio K100

Reviews:

Related manuals for HES Aperio K100

Brands by name

Popular brands