Assa Abloy Aperio AH15 Mechanical Installation Instructions Download Page 7

Page: 7 / 52

Aperio

Online Mechanical Installation Guide, Document No: ST-001323-B Date: 21 februari 2014

Aperio

Online

4 Mechanical Installation

This chapter includes guidelines for selecting the

correct installation place for communication hubs

in an Aperio online EAC system.

This chapter also describes how to connect the

communication hubs to the power supply.

Mechanical installation AH15

Minimum distance between AH15 communica-

tion hubs

If necessary, several communications hubs can

be positioned together with a minimum of 0.2

meter in between the hubs (or use one AH30

communication hub to pair with all three locks).

X > 0.2 m / ~ 8 in

Figure 3.

Minimum

distance between

AH15 communi-

cation hubs with

E100 locks

Summary of Contents for Aperio AH15





















































Search results

Summary of Contents for Aperio AH15

Reviews:

Related manuals for Aperio AH15

Brands by name

Popular brands

Assa Abloy Aperio AH15, Mechanical Installation Instructions

Search results

Summary of Contents for Aperio AH15

Reviews:

Related manuals for Aperio AH15

Brands by name

Popular brands