Assa Abloy Aperio AH15 Mechanical Installation Instructions Download Page 31

Page: 31 / 52

Aperio

Online Mechanical Installation Guide, Document No: ST-001323-B Date: 21 februari 2014

Aperio

Online

Connecting to the Wiegand bus

The AH15 communication hub has four Wiegand

signals plus ground. Purpose and connection of

these signals are described in the table below.

8-24V

GND

GREEN

RED

DATA0

DATA1

RS485 B

RS485 A

Hub connector

designation

Description

Connect to…

8-24V

Positive voltage

EAC power supply.

GND

Ground

EAC system ground.

GREEN

Wiegand Green LED signal. Input to

communication hub. Used for access decision.

Wiegand Green LED output on EAC system.

Alternatively, connect to a lock control relay output

on EAC system.

RED

Wiegand Red LED signal. Input to communication

hub. Used for access decision.

Wiegand Red LED output on EAC system.

Alternatively, leave unconnected if signal is selected

not to be used by DIP switch 1.

DATA0

Wiegand Data 0 signal. Output from

communication hub. Used to transmit credentials. Wiegand Data 0 on EAC system.

DATA1

Wiegand Data 1 signal. Output from

communication hub. Used to transmit credentials. Wiegand Data 1 on EAC system.

RS485 B

NOT APPLICABLE

RS485 A

NOT APPLICABLE

Connecting to supply voltage

Connect the wires to 8-24 VDC, 0.9 W and GND

(ground) on the communication hub.

Note! The power supply shall be a Limited Power

Source (LPS) according to EN 60950-1. The power

supply shall be 3 A over current protected. Wire

requirements 16-22 AWG.

Summary of Contents for Aperio AH15





















































Search results

Summary of Contents for Aperio AH15

Reviews:

Related manuals for Aperio AH15

Brands by name

Popular brands

Assa Abloy Aperio AH15, Mechanical Installation Instructions

Search results

Summary of Contents for Aperio AH15

Reviews:

Related manuals for Aperio AH15

Brands by name

Popular brands